Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307115
  1. Install the front door inside locking cable assembly as shown in the illustration.



    B307116
  1. Engage the 3 claws as shown in the illustration.



2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307117
  1. Install the front door lock remote control cable assembly as shown in the illustration.



3. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.

  1. When reusing the front door lock assembly:

    1. Install a new door lock wiring harness seal to the front door lock assembly.



    B307118E01
  1. Insert the front door lock open rod to the front door lock assembly.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

    HINT:
    Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    B307098
  1. Install the front door outside handle cover with lock cylinder assembly.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B299844
  1. Install the hole plug.



5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B307095
  1. Engage the guide.

  1. Install the front door rear lower frame sub-assembly with the bolt.



6. INSTALL FRONT DOOR GLASS RUN


    B307092
  1. Install the front door glass run.



7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.



    B307123
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

    NOTICE:
    Do not damage the front door glass.



    B307088
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B307087
  1. Install the front door No. 2 service hole cover.



8. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.

  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.



    B313978E01
  1. Attach the front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.



9. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
  1. Install the front No. 2 speaker assembly with the 2 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B307126E02
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly



    B307169
  1. Engage the 8 clips.



    B307081
  1. Install the front door trim board sub-assembly with the 3 screws.



    B307127
  1. Engage the claw and close the cover.



11. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect the connector.



    B307078
  1. Engage the 4 guides and 10 claws to install power window regulator master switch assembly with front door armrest base panel.



12. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect the connector.



    B307079
  1. Engage the 4 guides and 10 claws to install power window regulator switch assembly with front door armrest base panel.



13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



14. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



15. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)


16. CHECK POWER WINDOW CONTROL SYSTEM
(Click here)