Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL

UPPER INSTRUMENT PANEL > INSTALLATION

for Preparation Click here



1. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY


  1. When using a new instrument panel sub-assembly:



    1. Immediately before installing the upper instrument panel assembly, twist and cut off the portion shown in the illustration.


      B301706



  1. Push the upper instrument panel assembly in the direction indicated by the arrow (1) to engage the 5 guides.


    B301693E01

  1. Push the upper instrument panel assembly in the direction indicated by the arrow (2) to engage the 7 clips to install the upper instrument panel assembly.

  1. Install the bolt <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the screw <C>.

  1. Install the 2 clips.

  1. w/ Navigation System:

    1. Connect the connector.



2. CONNECT NO. 2 INSTRUMENT PANEL WIRE
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B300246
  1. Connect the connector.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.



3. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B299869E01
  1. Align the alignment mark (Yellow green) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow green)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



5. INSTALL FRONT PILLAR GARNISH LH
  1. Remove the protective cover.

  1. Make sure that the front pillar garnish clip is not damaged.

    NOTICE:
    If there is any damage, replace the garnish clip with a new one.



    E276148E01
  1. Push the front pillar garnish LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides.
    Text in Illustration 
    *a
    Protective Tape

  1. Using needle-nose pliers with the tips wrapped with protective tape, bend the end of the front pillar garnish clip in the direction indicated by the arrow (2) shown in the illustration.

  1. Push the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration and insert it to the front pillar garnish clip.

  1. Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip in the direction indicated by the arrow (4) shown in the illustration.

    HINT:
    Rotate the front pillar garnish clip so that the longer end of the front pillar garnish clip is positioned at the bottom.

  1. Using needle-nose pliers with the tips wrapped with protective tape, push the front pillar garnish clip in the direction indicated by the arrow (5) and rotate it to the position shown in the illustration.

    HINT:
    Make sure that the front pillar garnish clip is positioned as shown in the illustration. Failing to do so may cause a gap between the front pillar garnish LH and roof headlining assembly.



    E276149E01
  1. Engage the clip and front pillar garnish clip to install the front pillar garnish LH.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    NOTICE:
    If there is a gap between the front pillar garnish LH and roof headlining assembly, the front pillar garnish clip is not installed correctly. While lightly pressing the front pillar garnish LH as shown in the illustration, push it towards the front pillar garnish clip side.

    HINT:
    Make sure that the curtain shield airbag assembly LH is not pinched.



6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B299871E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



7. INSTALL COMBINATION METER ASSEMBLY
  1. Engage the clamp.

  1. Connect the 2 connectors.



    E244447
  1. Engage the 3 clips.

  1. Install the combination meter assembly with the 2 screws.



8. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Engage the 9 guides and 4 claws.

  1. Install the instrument cluster finish panel sub-assembly with the 2 clips.



9. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
  1. Engage the claw and 4 clips, to install the center instrument panel register assembly.



10. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B301686
  1. Engage the 10 guides and 12 clips to install the instrument cluster finish panel garnish.



11. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)
  1. Engage the 3 clips to install the No. 2 instrument panel register assembly.



12. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for RHD)
  1. Engage the 3 clips to install the No. 1 instrument panel register assembly.



13. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B301682
  1. Engage the claw and 8 clips to install the center instrument cluster finish panel sub-assembly.



14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



15. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



16. INSPECT SRS WARNING LIGHT
(Click here)