Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › ELECTRIC VEHICLE CONVERTER

ELECTRIC VEHICLE CONVERTER > REASSEMBLY

for Preparation Click here


NOTICE:
Do not cross-thread the bolts when installing them.

HINT:
Prepare 2 tubes of thermal grease X-23-7884-4 when replacing the hybrid vehicle converter kit.
  1. For Europe : 08887-83080
  2. For except Europe : 08887-02809



1. REMOVE THERMAL GREASE


    A360150E02
  1. Working with another person, install the 4 bolts and 4 nuts to the power module intelligent transistor kit.
    Text in Illustration 
    *1
    Bolt
    *2
    Nut
    *3
    Antistatic Mat

  1. Place the power module intelligent transistor kit on an antistatic mat.

  1. Using a scraper with its tip wrapped with protective tape, remove any remaining thermal grease from the power module intelligent transistor kit.

    NOTICE:
    1. Do not touch the circuit board.
    2. Do not apply excessive force to the center of the power module intelligent transistor kit.
    3. Keep the parts free from foreign matter.
    4. Keep thermal grease away from other parts.
    5. Do not spray non-residue solvent directly onto the parts when cleaning.
    6. Clean parts with a piece of cloth saturated with non-residue solvent.
    7. Do not use compressed air when cleaning to prevent dust from flying.

  1. Using a piece of cloth, remove the thermal grease.

  1. Working with another person, remove the 4 bolts and 4 nuts from the power module intelligent transistor kit.



2. REMOVE SEAL PACKING (FROM INVERTER CASE WITH CONDENSER CONTACT SURFACE)

NOTICE:
  1. Only remove seal packing which is uneven, has peeled off or seeped out from between the contact surfaces.
  2. Do not drop any removed seal packing into the inverter case with condenser.
  3. Do not bend the bus-bars.

  1. Set the inverter case with condenser on its side as shown in the illustration.

    NOTICE:
    To prevent the inverter case with condenser from falling over, hold it by hand or place an object behind it.



  1. Using a finger or a scraper with its tip wrapped with protective tape, remove any remaining seal packing which is uneven, has peeled off or seeped out from around the contact surface shown in the illustration and inside the bolt holes.


    A360151E02


    Text in Illustration 
    *1
    Seeped Out or Uneven Seal Packing
    *2
    Light Coat of Seal Packing Remaining on Contact Surface
    *a
    Minimum Requirement for Removal of Seal Packing
    -
    -



3. REMOVE ADHESIVE (FROM NO. 1 AND NO. 2 INVERTER DRAIN PLUGS SEALING SURFACE)


    A360152E02
  1. Remove the protective tape from the installation holes of the No. 1 and No. 2 inverter drain plugs.
    Text in Illustration 
    *1
    Protective Tape



    A360153E01
  1. Apply protective tape to the installation holes of the No. 1 and No. 2 inverter drain plugs from the inside of the inverter case with condenser.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not bend the bus-bars when applying protective tape.



  1. Using a scraper with its tip wrapped with protective tape, remove any remaining adhesive from the sealing surfaces of the No. 1 and No. 2 inverter drain plugs.


    A360154E01


    Text in Illustration 
    *1
    Sealing Surface
    -
    -

    NOTICE:
    Do not damage the sealing surfaces.

  1. Remove any adhesive shavings using tape or equivalent.

  1. Remove the protective tape from the inside of the inverter case with condenser.



    A360152E02
  1. Apply protective tape to the installation holes of the No. 1 and No. 2 inverter drain plugs as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



4. REMOVE RESIDUE (FROM INVERTER SIGNAL CONNECTOR COVER SEALING SURFACE)


    A360155E01
  1. Apply protective tape to the area shown in the illustration to prevent removed residue from entering the inverter case with condenser.
    Text in Illustration 
    *1
    Protective Tape



    A360156
  1. Using 600-grit sandpaper, remove the residue from each grommet sealing surface until it feels smooth.

    NOTICE:
    1. Use 600-grit or higher sandpaper.
    2. Do not allow removed residue to enter the inverter case with condenser or hybrid vehicle converter kit.
    3. Do not touch or allow grease or oil to contact the sealing surfaces of the inverter case with condenser.

  1. Remove any residue particles using tape or equivalent.

  1. Remove the protective tape.

  1. Thoroughly wash your hands after performing this step.

    HINT:
    It is not necessary to perform this step if performing the "Remove Residue (from Grommet Sealing Surface)" procedure next.



5. REMOVE RESIDUE (FROM GROMMET SEALING SURFACE)

HINT:
Perform the following procedure only when there is residue on the grommet sealing surfaces:



    A360157E01
  1. Apply protective tape to the areas shown in the illustration to prevent removed residue from entering the inverter case with condenser.
    Text in Illustration 
    *1
    Inverter Case with Condenser
    *2
    Protective Tape



  1. Using 600-grit sandpaper, remove the residue from each grommet sealing surface until it feels smooth.


    A360158E01


    Text in Illustration 
    *a
    Residue
    -
    -

    NOTICE:
    1. Use 600-grit or higher sandpaper.
    2. Do not allow removed residue to enter the inverter case with condenser

  1. Remove any adhesive shavings particles using tape or equivalent.

  1. Remove the protective tape.

  1. Thoroughly wash your hands after performing this step.



6. CLEAN INVERTER SIGNAL CONNECTOR COVER


    A314639E01
  1. Remove the gasket from the inverter signal connector cover. Wash the gasket and inverter signal connector cover with water and dry them completely.

    NOTICE:
    Do not damage the gasket.

    Text in Illustration 
    *1
    Gasket

  1. Thoroughly wash your hands after performing this step.



7. INSTALL POWER MODULE INTELLIGENT TRANSISTOR KIT

NOTICE:
  1. Do not touch the circuit board.
  2. Do not allow any moisture to come into contact with the circuit board.



    A360159E01
  1. Place the hybrid vehicle converter kit so that the guide pins are positioned as shown in the illustration and clean the thermal grease contacting area of the hybrid vehicle converter kit.
    Text in Illustration 
    *1
    Guide Pins
    *a
    Thermal Grease Contacting Area

    CAUTION:
    Do not apply non-residue solvent directly to the hybrid vehicle converter kit when cleaning.

    HINT:
    Clean the hybrid vehicle converter kit contact surfaces with a piece of cloth saturated with non-residue solvent.



    A360160E01
  1. Apply protective tape to the wire harness to keep it free from grease.
    Text in Illustration 
    *1
    Protective Tape



    A360161E01
  1. Apply protective tape to the hybrid vehicle converter kit as shown in the illustration to prevent grease from entering it.
    Text in Illustration 
    *1
    Protective Tape



    A362219E01
  1. Bend the masking seal as shown in the illustration.
    Text in Illustration 
    *1
    Do not remove

    NOTICE:
    Do not remove the release paper from the bent portion of the masking seal. If the adhesive surface of the masking seal contacts a bus-bar, the bus-bar may be bent when removing the masking seal.



    A362220
  1. Remove the release paper from the masking seal.

    NOTICE:
    Do not remove the release paper from the bent portion of the masking seal.



  1. Align the guide holes of the masking seal with the guide pins as shown in the illustration, and attach the masking seal to the hybrid vehicle converter kit.


    A362221E01


    Text in Illustration 
    *1
    Masking Seal
    *2
    Guide Pin
    *3
    Guide Hole
    -
    -



  1. Check that the masking seal is attached correctly, then firmly press on it with your fingers to securely attach it.


    A362222

    NOTICE:
    1. Securely attach the masking seal without leaving any air bubbles.
    2. Do not touch the bus-bars when attaching the masking seal.



    A293968
  1. Gently squeeze the tube of thermal grease and apply a small amount to a piece of cloth.

    HINT:
    Some clear liquid may come out first. Squeeze it out completely onto a piece of cloth.



  1. Apply thermal grease to 14 places as shown in the illustration.


    A362224E02


    Text in Illustration 
    *a
    Reference Line
    *b
    Almost equally spaced
    *c
    Approximately 6.0 mm (0.236 in.)
    *d
    Approximately 2.0 mm (0.0787 in.)



    A362226E01
  1. Using SST, carefully apply the thermal grease smoothly and evenly by spreading it as shown in the illustration. (Procedure A)

    SST
    09891-47010  
    Text in Illustration 
    *1
    SST
    *a
    45°

    NOTICE:
    1. Before performing work, check that the thermal grease contacting area of SST is not damaged.
    2. Apply the thermal grease smoothly and evenly to ensure proper heat transfer.
    3. Keep SST at a 45-degree angle and perform work carefully.



  1. Change the orientation of SST as shown in the illustration. (Procedure B)


    A362228E01


    Text in Illustration 
    *1
    SST
    -
    -
    *a
    45°
    -
    -



    A362230E01
  1. Using SST, carefully apply the thermal grease smoothly and evenly by spreading it as shown in the illustration. (Procedure C)
    Text in Illustration 
    *1
    SST
    *a
    45°

  1. Repeat steps A through C until the thermal grease is smooth and even.



    A362232
  1. Check that the thermal grease has been applied smoothly and evenly.



    A300967
  1. If the thermal grease layer is uneven and the application surface is visible, apply more thermal grease.

  1. Using SST, carefully apply the thermal grease smoothly and evenly.

    NOTICE:
    1. Apply the thermal grease smoothly and evenly to ensure proper heat transfer.
    2. Keep SST at a 45-degree angle and perform work carefully.



    A300968
  1. If foreign matter has attached to the thermal grease, scrape it off using the edge of the thermal grease tube, and apply more thermal grease.

  1. Using SST, carefully apply the thermal grease smoothly and evenly.

    NOTICE:
    1. Apply the thermal grease smoothly and evenly to ensure proper heat transfer.
    2. Keep SST at a 45-degree angle and perform work carefully.

  1. Check that the thermal grease has been applied smoothly and evenly.



    A362233E01
  1. Remove the masking seal from the hybrid vehicle converter kit.
    Text in Illustration 
    *1
    Bus-bar
    *a
    Remove

    NOTICE:
    1. Slowly remove the masking seal without touching the thermal grease surface.
    2. Be careful not to touch the bus-bars when removing the masking seal.

  1. Remove the protective tape.



  1. Align the guide holes with the guide pins as shown in the illustration, and temporarily install the power module intelligent transistor kit to the hybrid vehicle converter kit.


    A360162E01


    Text in Illustration 
    *1
    Guide Pins
    *2
    Guide Hole (Oblong Hole)
    *3
    Guide Hole (Circular Hole)
    -
    -

    NOTICE:
    1. Do not apply any force the coolant pipes.
    2. Make sure to align the guide pins correctly.
    3. Be careful not to deform the bus-bars.

  1. Install the power module intelligent transistor kit with the 4 bolts.



    A359881E01
  1. Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    A359880
  1. Install the 3 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not touch the bus-bars.



8. INSTALL MG CONTROL COMPUTER WITH BRACKET SUB-ASSEMBLY

NOTICE:
  1. Do not touch the circuit board.
  2. Do not allow any moisture to come into contact with the circuit board.



  1. Align the guide pins of the MG control computer with bracket sub-assembly with the holes of the hybrid vehicle converter kit and temporarily install the MG control computer with bracket sub-assembly to the hybrid vehicle converter kit.


    A360163E01


    Text in Illustration 
    *1
    Guide Pins
    -
    -

    NOTICE:
    Make sure to align the guide pins correctly.

  1. Install the MG control computer with bracket sub-assembly with the 4 bolts.



    A359878E01
  1. Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }



  1. Engage the 2 wire harnesses to the 4 clamps.


    A360164



    A359879
  1. Connect the connector.



    A359876
  1. Connect the 2 connectors.



    A359875
  1. Disengage the lock claws of the white resin connector and connect the flat cable to the power module intelligent transistor kit.



  1. Check that the flat cable is connected securely.

    NOTICE:
    A317060
    If the flat cable is not fully connected, connect it securely.



    A360165E01
  1. If the gasket of the inverter signal connector is protruding, fully push it in.
    Text in Illustration 
    *1
    Gasket

    HINT:
    A317062E01
    If the gasket is misaligned, install it so that each mark is at the center of each side.
    Text in Illustration 
    *1
    Gasket
    *2
    Mark



9. INSTALL INVERTER TERMINAL WITH SENSOR SUB-ASSEMBLY

NOTICE:
  1. Do not touch the circuit board.
  2. Do not allow any moisture to come into contact with the circuit board.



  1. Align the guide pins of the inverter terminal with sensor sub-assembly with the holes of the hybrid vehicle converter kit and temporarily install the inverter terminal with sensor sub-assembly to the hybrid vehicle converter kit.


    A360166E01


    Text in Illustration 
    *1
    Guide Pins
    -
    -

    NOTICE:
    Make sure to align the guide pins correctly.

  1. Install the inverter terminal with sensor sub-assembly with the 4 bolts.



    A359874E01
  1. Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }



    A359872
  1. Connect the 3 connectors.



  1. Check the installation condition of the pen sheet.

    NOTICE:
    1. Do not touch the circuit board.
    2. Do not allow any moisture to come into contact with the circuit board.




    1. While ensuring that the pen sheet does not interfere with components of the circuit board, insert the pen sheet between the inverter terminal with sensor sub-assembly and MG control computer with bracket sub-assembly.


      A360167E01


      Text in Illustration 
      *1
      Pen Sheet
      -
      -



    2. A360168E01
    3. Set the pen sheet so that the guide hole is aligned with the pin of the motor generator control computer sub-assembly as shown in the illustration.
      Text in Illustration 
      *1
      Guide Pin
      *2
      Double-sided Tape
      *3
      Pen Sheet

    4. Attach the double-sided tape of the pen sheet to the connector as shown in the illustration.



    A359873
  1. Install the 6 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not touch the bus-bars.



10. INSTALL INVERTER CASE WITH CONDENSER

NOTICE:
  1. Do not touch the circuit board.
  2. Do not allow any moisture to come into contact with the circuit board.
  3. Do not touch or allow grease or oil to contact the sealing surfaces of the hybrid vehicle converter kit and inverter case with condenser.



  1. Apply seal packing (diameter: 2.0 to 3.0 mm (0.0787 to 0.118 in.)) in a continuous line to the locations shown in the illustration.


    A360169E01


    Text in Illustration 
    *1
    Seal Packing
    *2
    Bolt Hole
    *3
    Coolant Pipe
    -
    -
    *a
    2.0 to 3.0 mm (0.0787 to 0.118 in.)
    *b
    2.0 to 3.0 mm (0.0787 to 0.118 in.)
    *c
    Around Coolant Pipe
    -
    -

    Seal Packing:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. Install the inverter case with condenser within 3 minutes of applying seal packing.
    2. Tighten the bolts within 15 minutes of applying seal packing.
    3. Keep the coolant pipes free from seal packing.



  1. Install the inverter case with condenser.



      A360170E01
    1. Peel back the protective tape to the extent that the following steps can be performed.
      Text in Illustration 
      *1
      Protective Tape

      NOTICE:
      Do not touch or allow grease or oil to contact the sealing surfaces of the inverter case with condenser.



    2. Align the holes of the inverter case with condenser with the guide pins of the hybrid vehicle converter kit and temporarily install the inverter case with condenser so that the bus-bar (A) does not contact the protrusion of the inverter terminal with sensor sub-assembly (B).


      A360171E01


      Text in Illustration 
      *1
      Guide Pins
      -
      -

      NOTICE:
      1. Make sure to align the guide pins correctly.

      2. A360172
        Check that the bus-bars of the hybrid vehicle converter kit overlap the bus-bars of the inverter case with condenser.

      3. A360173E01
        Make sure that the bus-bar (A) is not resting on the resin part of the inverter terminal with sensor sub-assembly as shown in the illustration.

      Text in Illustration 
      *1
      Bus-bar (A)



    A359778
  1. Temporarily install the inverter case with condenser with the 11 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Fully tighten the 11 bolts.

    Torque:
    9.2 N*m{ 94 kgf*cm , 81 in.*lbf }



    A359776
  1. Install the 5 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not touch the bus-bars.



11. INSTALL INVERTER UNION GROMMET


    A315660E01
  1. Apply a light coat of seal packing to 2 new inverter union grommets.
    Text in Illustration 
    *1
    Seal Packing

    Seal Packing:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. Install the inverter union grommets within 60 minutes of installing the inverter case with condenser.
    2. Apply a light coat of seal packing to the entire surface of the area shown in the illustration. If seal packing is applied excessively, it may seep out, however, sealing quality will not be affected.
    3. Install the inverter union grommets within 3 minutes of applying seal packing.



    A360174E01
  1. Push in the inverter union grommet until it passes over the flange of the coolant pipe.
    Text in Illustration 
    *1
    Coolant Pipe
    *2
    Inverter Union Grommet
    *a
    Flange

    NOTICE:
    Do not damage the coolant pipes.



    A360175E01
  1. Using a 30 mm socket, install the inverter union grommet.
    Text in Illustration 
    *1
    30 mm Socket

    HINT:
    A360176E01
    Make sure that the clearance between the inverter union grommet and inverter case with condenser is 2.0 mm (0.0787 in.) or less.
    Text in Illustration 
    *a
    2.0 mm (0.0787 in.) or less

  1. Perform the same procedure to install the other inverter union grommet.



12. INSTALL NO. 1 AND NO. 2 INVERTER DRAIN PLUGS

NOTICE:
Do not touch or allow grease or oil to contact the sealing surfaces of the inverter case with condenser.



    A348655E01
  1. Make sure that the sealing surfaces of the No. 1 and No. 2 inverter drain plugs are covered with aluminum tape.
    Text in Illustration 
    *1
    Aluminum Tape

    NOTICE:
    If the sealing surfaces of the No. 1 and No. 2 inverter drain plugs are not covered with aluminum tape, do not use them as they cannot be securely installed with only seal packing.



    A350409E01
  1. Remove the release film from the No. 1 and No. 2 inverter drain plugs.
    Text in Illustration 
    *1
    Release Film



    A315650E01
  1. Apply seal packing (diameter: 3.0 mm (0.118 in.)) to new No. 1 and No. 2 inverter drain plugs.
    Text in Illustration 
    *1
    No. 1 Inverter Drain Plug
    *2
    No. 2 Inverter Drain Plug
    *3
    Seal Packing
    *a
    Approximately 3.0 mm (0.118 in.)
    *b
    Approximately 3.0 mm (0.118 in.)

    Seal Packing:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. Be sure to use the specified type of seal packing.
    2. Install the No. 1 and No. 2 inverter drain plugs within 3 minutes of applying seal packing.



    A360177E01
  1. Install the No. 1 and No. 2 inverter drain plugs to the inverter with converter assembly.
    Text in Illustration 
    *1
    No. 1 Inverter Drain Plug
    *2
    No. 2 Inverter Drain Plug



13. INSTALL INVERTER SIGNAL CONNECTOR COVER


    A314639E03
  1. Install the gasket to the inverter signal connector cover.

    HINT:
    Make sure that the protrusion (A) of the gasket is securely inserted into the groove of the inverter signal connector cover.

    Text in Illustration 
    *1
    Gasket

  1. Clean the installation surface.



    A359770E01
  1. Install the inverter signal connector cover with the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    Text in Illustration 
    *1
    Inverter Signal Connector Cover



14. INSTALL NO. 2 ENGINE ROOM WIRE


    A359775
  1. Engage the clamp.

  1. Install the No. 2 engine room wire to the inverter with converter assembly with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Check that the nut is not cross-threaded and the terminal is not loose.



    A359774
  1. Close the terminal cover and engage the 2 claws.



15. INSTALL INVERTER COVER


    A360178E01
  1. Remove the protective tape.
    Text in Illustration 
    *1
    Protective Tape



    A359767
  1. Temporarily install the inverter cover with the 7 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.

    NOTICE:
    Visually confirm that the inverter cover waterproofing rubber is securely installed before installing the inverter cover.



16. INSTALL INVERTER TERMINAL COVER


    A359766E01
  1. Temporarily install the inverter terminal cover to the inverter with converter assembly with the 2 bolts.
    Text in Illustration 
    *1
    Interlock Connector

    NOTICE:
    1. Visually confirm that the inverter terminal cover waterproofing rubber is securely installed before installing the inverter terminal cover.
    2. Make sure that the interlock connector is fully engaged.



17. INSTALL INVERTER WITH CONVERTER ASSEMBLY
Click here


18. CHECK FOR COOLANT LEAK (for Inverter)
  1. Remove the reserve tank cap.

    CAUTION:
    Do not remove the reserve tank cap while the coolant (for inverter) is still hot. Pressurized, hot coolant and steam may be released and cause serious burns,



    A266680
  1. Install the radiator cap tester.

  1. Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17.7 psi), and then check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator, water pump, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

  1. Install the reserve tank cap.



19. OPERATION CHECK

HINT:
  1. After performing repair, check the operation as follows. Then check for DTCs again.
  2. The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flow at the auxiliary battery instead.



    A174427E02
  1. Connect an AC/DC 400 A probe from an ammeter to the positive (+) auxiliary battery cable.

  1. Turn the power switch on (READY) and leave the vehicle as is until the electric current flowing into the auxiliary battery becomes 10 A or less.



    A174428E02
  1. Change the orientation of the AC/DC 400A probe.

  1. Measure the current flowing from the auxiliary battery with the power switch on (READY), the high beam headlights on and blower motor switch in the HI position, and rear window defogger turned on.

    Standard Current:
    Item
    Switch Condition
    Specified Condition
    Current flowing from auxiliary battery
    Power switch on (READY)
    (High beam headlights on and blower motor switch in HI position, rear window defogger on)
    0 A or less
    (No current from auxiliary battery)

  1. Turn the power switch off.