MOTOR GENERATOR CONTROL COMPUTER > REASSEMBLY |
| 1. REMOVE SEAL PACKING (FROM HYBRID CONVERTER KIT CONTACT SURFACE) |
![]() |
Put clean pieces of paper into the areas shown in the illustration to prevent any remaining seal packing from entering the hybrid vehicle converter kit.
| *1 | Paper |
Using a finger or a scraper with its tip wrapped with protective tape, remove any remaining seal packing which is uneven, has peeled off or seeped out from around the contact surface shown in the illustration and inside the bolt holes.

| *1 | Paper | *2 | Seeped Out or Uneven Seal Packing |
| *3 | Light Coat of Seal Packing Remaining on Contact Surface | - | - |
| *a | Minimum Requirement for Removal of Seal Packing | - | - |
| 2. REMOVE SEAL PACKING (FROM INVERTER CASE WITH CONDENSER CONTACT SURFACE) |
Set the inverter case with condenser on its side as shown in the illustration.
Using a finger or a scraper with its tip wrapped with protective tape, remove any remaining seal packing which is uneven, has peeled off or seeped out from around the contact surface shown in the illustration and inside the bolt holes.

| *1 | Seeped Out or Uneven Seal Packing | *2 | Light Coat of Seal Packing Remaining on Contact Surface |
| *a | Minimum Requirement for Removal of Seal Packing | - | - |
| 3. REMOVE ADHESIVE (FROM NO. 1 AND NO. 2 INVERTER DRAIN PLUGS SEALING SURFACE) |
![]() |
Remove the protective tape from the installation holes of the No. 1 and No. 2 inverter drain plugs.
| *1 | Protective Tape |
![]() |
Apply protective tape to the installation holes of the No. 1 and No. 2 inverter drain plugs from the inside of the inverter case with condenser.
| *1 | Protective Tape |
Using a scraper with its tip wrapped with protective tape, remove any remaining adhesive from the sealing surfaces of the No. 1 and No. 2 inverter drain plugs.

| *a | Sealing Surface | - | - |
Remove any adhesive shavings using tape or equivalent.
Remove the protective tape from the inside of the inverter case with condenser.
![]() |
Apply protective tape to the installation holes of the No. 1 and No. 2 inverter drain plugs as shown in the illustration.
| *1 | Protective Tape |
| 4. REMOVE RESIDUE (FROM INVERTER SIGNAL CONNECTOR COVER SEALING SURFACE) |
![]() |
Apply protective tape to the area shown in the illustration to prevent removed residue from entering the inverter case with condenser.
| *1 | Protective Tape |
![]() |
Using 600-grit sandpaper, remove the residue from each grommet sealing surface until it feels smooth.
Remove any residue particles using tape or equivalent.
Remove the protective tape.
Thoroughly wash your hands after performing this step.
| 5. REMOVE RESIDUE (FROM GROMMET SEALING SURFACE) |
Apply protective tape to the areas shown in the illustration to prevent removed residue from entering the inverter case with condenser and hybrid vehicle converter kit.

| *1 | Inverter Case with Condenser | *2 | Hybrid Vehicle Converter Kit |
| *3 | Power Module Intelligent Transistor Kit | 4 | Protective Tape |
Using 600-grit sandpaper, remove the residue from each grommet sealing surface until it feels smooth.

| *a | Residue | - | - |
Remove any adhesive shavings particles using tape or equivalent.
Remove the protective tape.
Thoroughly wash your hands after performing this step.
| 6. CLEAN INVERTER SIGNAL CONNECTOR COVER |
![]() |
Remove the gasket from the inverter signal connector cover. Wash the gasket and inverter signal connector cover with water and dry them completely.
| *1 | Gasket |
Thoroughly wash your hands after performing this step.
| 7. INSTALL MG CONTROL COMPUTER WITH BRACKET SUB-ASSEMBLY |
Align the guide pins of the MG control computer with bracket sub-assembly with the holes of the hybrid vehicle converter kit and temporarily install the MG control computer with bracket sub-assembly to the hybrid vehicle converter kit.

| *1 | Guide Pins | - | - |
Install the MG control computer with bracket sub-assembly with the 4 bolts.
![]() |
Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.
Engage the 2 wire harnesses to the 4 clamps.

![]() |
Connect the connector.
![]() |
Connect the 2 connectors.
![]() |
Disengage the lock claws of the white resin connector and connect the flat cable to the power module intelligent transistor kit.
Check that the flat cable is connected securely.
![]() |
![]() |
If the gasket of the inverter signal connector is protruding, fully push it in.
| *1 | Gasket |
![]() |
| *1 | Gasket |
| *2 | Mark |
| 8. INSTALL INVERTER TERMINAL WITH SENSOR SUB-ASSEMBLY |
Align the guide pins of the inverter terminal with sensor sub-assembly with the holes of the hybrid vehicle converter kit and temporarily install the inverter terminal with sensor sub-assembly to the hybrid vehicle converter kit.

| *1 | Guide Pins | - | - |
Install the inverter terminal with sensor sub-assembly with the 4 bolts.
![]() |
Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.
![]() |
Connect the 3 connectors.
Check the installation condition of the pen sheet.
While ensuring that the pen sheet does not interfere with components of the circuit board, insert the pen sheet between the inverter terminal with sensor sub-assembly and MG control computer with bracket sub-assembly.

| *1 | Pen Sheet | - | - |
![]() |
Set the pen sheet so that the guide hole is aligned with the pin of the MG control computer sub-assembly as shown in the illustration.
| *1 | Guide Pin |
| *2 | Double-sided Tape |
| *3 | Pen Sheet |
Attach the double-sided tape of the pen sheet to the connector as shown in the illustration.
![]() |
Install the 6 bolts.
![]() |
If the No. 2 engine room wire is installed, install the bolt (A) using SST as shown in the illustration.
| *1 | SST |
![]() |
| *1 | SST |
| *2 | Length of SST 150 mm (5.91 in.) |
| *3 | Length of Torque Wrench 185 mm (7.28 in.) |
| 9. INSTALL INVERTER CASE WITH CONDENSER |
Apply seal packing (diameter: 2.0 to 3.0 mm (0.0787 to 0.118 in.)) in a continuous line to the locations shown in the illustration.

| *1 | Seal Packing | *2 | Bolt Hole |
| *3 | Coolant Pipes | - | - |
| *a | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | *b | 2.0 to 3.0 mm (0.0787 to 0.118 in.) |
| *c | Around Coolant Pipe | - | - |
Install the inverter case with condenser.
![]() |
Peel back the protective tape to the extent that the following steps can be performed.
| *1 | Protective Tape |
Align the holes of the inverter case with condenser with the guide pins of the hybrid vehicle converter kit so that the bus-bar (A) does not contact the protrusion of the inverter terminal with sensor sub-assembly (B).

| *1 | Guide Pins | - | - |
![]() |
![]() |
| *1 | Bus-bar (A) |
![]() |
Temporarily install the inverter case with condenser with the 11 bolts.
Fully tighten the 11 bolts.
![]() |
Install the 5 bolts.
![]() |
Install the No. 2 engine room wire to the inverter with converter assembly with the nut.
![]() |
Close the terminal cover and engage the 2 claws.
| 10. INSTALL INVERTER UNION GROMMET |
![]() |
Apply a light coat of seal packing to 2 new inverter union grommets.
| *1 | Seal Packing |
![]() |
Push in the inverter union grommet until it passes over the flange of the coolant pipe.
| *1 | Coolant Pipe |
| *2 | Inverter Union Grommet |
| *a | Flange |
![]() |
Using a 30 mm socket, install the inverter union grommet.
| *1 | 30 mm Socket |
![]() |
| *a | 2.0 mm (0.0787 in.) or less |
Perform the same procedure to install the other inverter union grommet.
| 11. INSTALL NO. 1 AND NO. 2 INVERTER DRAIN PLUGS |
![]() |
Make sure that the sealing surfaces of the No. 1 and No. 2 inverter drain plugs are covered with aluminum tape.
| *1 | Aluminum Tape |
![]() |
Remove the release film from the No. 1 and No. 2 inverter drain plugs.
| *1 | Release Film |
![]() |
Apply seal packing (diameter: 3.0 mm (0.118 in.)) to new No. 1 and No. 2 inverter drain plugs.
| *1 | No. 1 Inverter Drain Plug |
| *2 | No. 2 Inverter Drain Plug |
| *3 | Seal Packing |
| *a | Approximately 3.0 mm (0.118 in.) |
| *b | Approximately 3.0 mm (0.118 in.) |
![]() |
Install the No. 1 and No. 2 inverter drain plugs to the inverter with converter assembly.
| *1 | No. 1 Inverter Drain Plug |
| *2 | No. 2 Inverter Drain Plug |
| 12. INSTALL INVERTER SIGNAL CONNECTOR COVER |
![]() |
Install the gasket to the inverter signal connector cover.
| *1 | Gasket |
Clean the installation surface.
![]() |
Install the inverter signal connector cover with the 4 bolts.
| *1 | Inverter Signal Connector Cover |
| 13. INSTALL INVERTER COVER |
![]() |
Remove the protective tape.
| *1 | Protective Tape |
![]() |
Temporarily install the inverter cover with the 7 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.
| 14. INSTALL INVERTER TERMINAL COVER |
![]() |
Temporarily install the inverter terminal cover to the inverter with converter assembly with the 2 bolts.
| *1 | Interlock Connector |
| 15. INSTALL INVERTER WITH CONVERTER ASSEMBLY |
| 16. CHECK FOR COOLANT LEAK (for Inverter) |
Remove the reserve tank cap.
![]() |
Install the radiator cap tester.
Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17.7 psi), and then check that the pressure does not drop.
Install the reserve tank cap.
| 17. OPERATION CHECK |
![]() |
Connect an AC/DC 400 A probe from an ammeter to the positive (+) auxiliary battery cable.
Turn the power switch on (READY) and leave the vehicle as is until the electric current flowing into the auxiliary battery becomes 10 A or less.
![]() |
Change the orientation of the AC/DC 400A probe.
Measure the current flowing from the auxiliary battery with the power switch on (READY), the high beam headlights on and blower motor switch in the HI position, and rear window defogger turned on.
| Item | Switch Condition | Specified Condition |
| Current flowing from auxiliary battery | Power switch on (READY) (High beam headlights on and blower motor switch in HI position, rear window defogger on) | 0 A or less (No current from auxiliary battery) |
Turn the power switch off.