Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0560-117    System Voltage

for Preparation Click here


DESCRIPTION

  1. Battery power is constantly supplied to the BATT terminal of the hybrid vehicle control ECU to allow DTCs and freeze frame data to be retained in memory even though the power switch is turned off. The back-up power is supplied even when the power switch is off.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0560
117
Malfunction in the hybrid vehicle control ECU back-up power source circuit
(1 trip detection logic)
  1. Auxiliary battery
  2. ECU-B NO. 2 fuse
  3. Wire harness or connector
  4. Hybrid vehicle control ECU

Related Data List 
DTC No.
Data List
P0560-117
+B

WIRING DIAGRAM


A344504E03


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for a few seconds.

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A279820E01
  1. Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors (Click here).
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


2.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
  1. Check the connection of the auxiliary battery terminal.

    OK:
    The terminal is connected securely and there is no contact problem.



NG
CONNECT SECURELY
OK


3.INSPECT AUXILIARY BATTERY
(Click here)


NG
CHARGE OR REPLACE AUXILIARY BATTERY
OK


4.CHECK FUSE (ECU-B NO. 2)
  1. Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.



    A263622E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    ECU-B NO. 2 fuse
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    ECU-B NO. 2 Fuse

  1. Install the ECU-B NO. 2 fuse.



NG
REPLACE FUSE (ECU-B NO. 2)
OK


5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)
  1. Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Disconnect connector G81 from the hybrid vehicle control ECU.



  1. Measure the resistance according to the value(s) in the table below.

    NOTICE:
    When taking measurements with a tester, do not apply excessive force to the tester probes to avoid damaging the fuse holder or terminals.


    A344604E02


    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    ECU-B NO. 2 Fuse
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)
    -
    -

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    G81-3 (BATT) - 2 (ECU-B NO. 2 fuse)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    G81-3 (BATT) or 2 (ECU-B NO. 2 fuse) - Body ground and other terminals
    Power switch off
    10 kΩ or more

  1. Install the ECU-B NO. 2 fuse.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - AUXILIARY BATTERY POSITIVE TERMINAL)
  1. Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.



    A263624E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (ECU-B NO. 2 fuse) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    ECU-B NO. 2 Fuse

  1. Install the ECU-B NO. 2 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Recheck for DTCs.

    Result:
    Result
    Proceed to
    DTC P0560-117 is output again
    A
    DTC P0560-117 is not output
    B

HINT:
If DTC P0560-117 is output after this inspection, replace the hybrid vehicle control ECU. If the DTC is not output, check for intermittent problems (Click here) because there may be a malfunction in the wire harness or connector.



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)