Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0225119 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2322  Front Passenger Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2322 Front Passenger Side Door ECU Communication Stop No communication between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for front passenger door)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

DOOR fuse



WIRING DIAGRAM

B441660E12
0.281,1.917 1.906,2.281 1.625,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.281,1.781 0.594,1.979 0.313,0.198 10 false MB 2.219,1.333 2.531,1.531 0.313,0.198 10 false 3H 2.208,1.469 3.844,1.813 1.635,0.344 10 false Instrument Panel Junction Block Assembly 4.156,1.948 6.76,2.344 2.604,0.396 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 4.146,1.781 5.302,2.01 1.156,0.229 10 false I2*1, J2*2 5.74,0.75 6.969,0.948 1.229,0.198 10 false DOOR 6.417,0.625 7.156,1.219 0.74,0.594 10 false from Auxiliary Battery 5.177,1.458 5.74,1.656 0.563,0.198 10 false GND 5.552,1.333 6.115,1.531 0.563,0.198 10 false 1 5.344,0.615 5.906,0.813 0.563,0.198 10 false B 5.552,0.49 6.115,0.688 0.563,0.198 10 false 2 4.583,0.75 5.146,0.948 0.563,0.198 10 false LIN1 4.406,0.594 4.969,0.792 0.563,0.198 10 false 9 2.979,0.604 3.542,0.802 0.563,0.198 10 false 25 1.948,0.615 2.51,0.813 0.563,0.198 10 false 16 1.594,0.76 2.156,0.958 0.563,0.198 10 false LIN2 0.719,2.49 2.76,2.729 2.042,0.24 10 false : LIN Communication Line 2.719,2.198 4.354,2.542 1.635,0.344 10 false *1: for LHD 2.708,2.479 4.344,2.792 1.635,0.313 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B426689C01
2.083,1 2.417,1.25 0.333,0.25 5.5,0.75 5.833,1 0.333,0.25 2.198,2.156 2.198,1.573 false 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.156,1.052 2.469,1.25 0.313,0.198 10 false MB 5.583,0.802 5.896,1 0.313,0.198 10 false 3H 2.083,2.219 2.698,2.417 0.615,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))
a.

for LHD

i.

Disconnect the I2 power window regulator motor assembly (for front passenger door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - I2-9 (LIN) Power switch off Below 1 Ω
I2-9 (LIN) or 3H-25 - Body ground Power switch off 10 kΩ or higher




b.

for RHD

i.

Disconnect the J2 power window regulator motor assembly (for front passenger door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - J2-9 (LIN) Power switch off Below 1 Ω
J2-9 (LIN) or 3H-25 - Body ground Power switch off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door) - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door) - AUXILIARY BATTERY, BODY GROUND)
a.

for LHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I2-2 (B) - I2-1 (GND) Power Switch off 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (GND) - Body ground Always Below 1 Ω




b.

for RHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J2-2 (B) - J2-1 (GND) Power Switch off 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-1 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)
a.

Replace the power window regulator motor assembly (for front passenger door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2322 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)