Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM3210E _57 Power Source / Network _047508 POWER DISTRIBUTION _0227179 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Main body ECU (multiplex network body ECU) Perform code registration (Immobiliser system)
·

Entry and start system

·

Wireless door lock control system

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION (for RHD)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (for RHD)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73900 3.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 55308B 4.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)

Hide 55607 5.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL


Hide 55550 6.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL


Hide 82878 7.REMOVE ECU INTEGRATION BOX LH (for RHD)

Hide 8.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.

for LHD:

i.
E336519

Disconnect each connector.


ii.

Disengage the clamp.


iii.
E336520C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.


iv.
E336522C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut.


v.

Pull out the instrument panel junction block assembly with main body ECU.


vi.
E336523

Disengage the clamp.


vii.
E336524C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clamp.


viii.

Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.



b.

for RHD:

i.
E336510

Disconnect each connector.


ii.

Disengage the clamp.


iii.
E336512C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.


iv.
E336514C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut.


v.

Pull out the instrument panel junction block assembly with main body ECU.


vi.
E336515

Disengage the clamp.


vii.
E336516C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clamp.


viii.

Disengage the 2 claws and raise the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.



Hide 82715 9.REMOVE WIRING HARNESS CLAMP BRACKET (for LHD)

a.
E336526C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt.


b.

Disengage the claw and remove the wiring harness clamp bracket as shown in the illustration.


Hide 10.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E336530C01
0.188,2.813 0.51,2.813 true 0.719,2.854 1.135,2.854 true 1.167,2.76 1.479,2.917 0.313,0.156 10 false *1 0.031,2.719 0.344,2.875 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push in this Direction


Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.


b.
E336535C01
1.5,1.917 1.688,1.688 false 1.396,1.917 1.708,2.073 0.313,0.156 10 false *a
*a Protective Tape
V100135

Insert in this Direction
V113147

Remove in this Direction


With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E336537C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.