The front airbag sensor RH circuit consists of the airbag ECU assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1612/83 | Lost Communication with Front Airbag Sensor RH | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit. ·
Front airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B1613/83 | Front Airbag Sensor RH Initialization Incomplete | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit. ·
Front airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag ECU assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors that link the engine room main wire and instrument panel wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *3 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
*b | Front view of wire harness connector
(to Front Airbag Sensor RH) |
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (+SR) - A35-1 (-SR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the service wire from connector B.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (+SR) - A35-1 (-SR) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
- | - |
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (+SR) - Body ground | Power switch on (IG) | Below 1 V |
| A35-1 (-SR) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| A35-1 (-SR) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/o Passenger Airbag ON/OFF Indicator |
| *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor LH |
| *2 | Airbag ECU Assembly |
Connect the connector to the airbag ECU assembly.
Interchange the front airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. | A |
| DTC B1617/84 or B1618/84 is output. | B |
| DTC B1612/83 or B1613/83 is output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the front airbag sensor RH and LH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the instrument panel wire connector from the engine room main wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF5-4 (+SR) - Body ground | Always | 1 MΩ or higher |
| AF5-3 (-SR) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel wire connector from the engine room main wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
- | - |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF5-4 (+SR) - Body ground | Power switch on (IG) | Below 1 V |
| AF5-3 (-SR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel wire connector from the engine room main wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF5-4 (+SR) - AF5-3 (-SR) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel wire connector from the engine room main wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Front Airbag Sensor RH | *2 | Airbag ECU Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
*b | Front view of wire harness connector
(to Engine Room Main Wire) |
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF5-4 (+SR) - AF5-3 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG