Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag ECU assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1617/84 Lost Communication with Front Airbag Sensor LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1618/84 Front Airbag Sensor LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C238364E76
1.844,0.813 2.146,1.229 0.302,0.417 10 false 2 1.5,0.906 1.979,1.229 0.479,0.323 10 false +SL 1.844,1.979 2.115,2.313 0.271,0.333 10 false 1 1.542,2.073 2.021,2.385 0.479,0.313 10 false -SL 5.146,0.813 5.531,1.094 0.385,0.281 10 false 30 5.375,0.906 5.844,1.26 0.469,0.354 10 false +SL 5.156,1.979 5.427,2.302 0.271,0.323 10 false 28 3.458,0.906 3.865,1.271 0.406,0.365 10 false AF5 3.458,2.083 3.885,2.51 0.427,0.427 10 false AF5 3.542,1.885 3.76,2.188 0.219,0.302 10 false 1 3.542,0.719 3.771,1 0.229,0.281 10 false 2 5.375,2.083 5.813,2.417 0.438,0.333 10 false -SL 0.563,2.896 1.167,3.208 0.604,0.313 10 false A8 0.563,3.042 2.292,3.354 1.729,0.313 10 false Front Airbag Sensor LH 5.344,2.906 5.719,3.188 0.375,0.281 10 false F56 5.344,3.063 6.917,3.354 1.573,0.292 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
a.

Connect the connectors that link the engine room main wire and instrument panel wire.

C284131C03
0.75,2.948 1.063,3.156 0.313,0.208 1.135,0.51 1.479,0.74 0.344,0.229 4.729,0.521 5.073,0.75 0.344,0.229 4.344,2.948 4.656,3.156 0.313,0.208 2.177,0.76 1.99,0.948 false 1.563,3.031 1.74,3.365 false 2.25,0.979 2.25,1.115 false 5.854,0.99 5.854,1.125 false 5.781,0.76 5.573,0.948 false 2.333,0.771 2.521,0.958 false 1.365,3.031 1.188,3.365 false 4.969,3.031 4.792,3.365 false 5.167,3.021 5.344,3.354 false 5.927,0.76 6.125,0.958 false 0.167,0.146 0.479,0.396 0.313,0.25 10 false *A 3.677,0.146 3.979,0.396 0.302,0.25 10 false *B 1.135,0.25 1.448,0.448 0.313,0.198 10 false *a 4.74,0.25 5.052,0.448 0.313,0.198 10 false *a 0.688,2.656 1,2.854 0.313,0.198 10 false *b 4.281,2.656 4.594,2.854 0.313,0.198 10 false *b 0.635,1.708 0.948,1.906 0.313,0.198 10 false *1 4.229,1.917 4.542,2.115 0.313,0.198 10 false *1 6.24,1.917 6.552,2.115 0.313,0.198 10 false *2 2.646,1.948 2.958,2.146 0.313,0.198 10 false *2 2.292,1.719 2.448,1.917 0.156,0.198 10 false A 2.042,1.719 2.198,1.917 0.156,0.198 10 false B 1.667,1.719 1.823,1.917 0.156,0.198 10 false C 1.177,1.719 1.333,1.917 0.156,0.198 10 false E 0.927,1.719 1.083,1.917 0.156,0.198 10 false F 5.896,1.927 6.052,2.125 0.156,0.198 10 false A 5.646,1.927 5.802,2.125 0.156,0.198 10 false B 5.271,1.927 5.427,2.125 0.156,0.198 10 false C 1.542,1.719 1.698,1.917 0.156,0.198 10 false D 5.146,1.927 5.302,2.125 0.156,0.198 10 false D 4.771,1.927 4.927,2.125 0.156,0.198 10 false E 4.521,1.927 4.677,2.125 0.156,0.198 10 false F 1.198,0.552 1.531,0.802 0.333,0.25 10 false F56 0.823,2.979 1.188,3.24 0.365,0.26 10 false A8 2.167,1.135 2.417,1.344 0.25,0.208 10 false *3 5.771,1.146 6,1.354 0.229,0.208 10 false *3 1.76,0.885 2.073,1.094 0.313,0.208 10 false -SL 2.552,0.885 3.01,1.083 0.458,0.198 10 false +SL 1.052,3.375 1.51,3.573 0.458,0.198 10 false -SL 1.594,3.375 2.052,3.573 0.458,0.198 10 false +SL 4.646,3.385 4.99,3.615 0.344,0.229 10 false -SL 5.208,3.385 5.583,3.615 0.375,0.229 10 false +SL 6.135,0.896 6.542,1.156 0.406,0.26 10 false +SL 5.344,0.896 5.656,1.125 0.313,0.229 10 false -SL 4.781,0.552 5.115,0.802 0.333,0.25 10 false F56 4.427,2.979 4.792,3.24 0.365,0.26 10 false A8
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Service Wire - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)



b.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A8-2 (+SL) - A8-1 (-SL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

NG

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
a.

Disconnect the service wire from connector B.

C284128C06
0.698,1.781 1.021,2 0.323,0.219 4.354,1.781 4.677,2 0.323,0.219 1.156,2.313 1.396,1.969 false 1.813,2.313 1.583,1.979 false 4.792,2.323 5.031,1.979 false 5.469,2.313 5.24,1.979 false 0.167,0.083 0.51,0.313 0.344,0.229 10 false *A 3.677,0.104 4.052,0.375 0.375,0.271 10 false *B 0.667,0.542 1,0.833 0.333,0.292 10 false *1 2.646,0.771 3.021,1.073 0.375,0.302 10 false *2 0.573,1.448 0.927,1.75 0.354,0.302 10 false *a 4.313,0.552 4.646,0.844 0.333,0.292 10 false *1 6.302,0.552 6.677,0.854 0.375,0.302 10 false *2 2.302,0.552 2.677,0.854 0.375,0.302 10 false A 2.042,0.552 2.417,0.854 0.375,0.302 10 false B 1.677,0.552 2.052,0.854 0.375,0.302 10 false C 1.552,0.552 1.927,0.854 0.375,0.302 10 false D 1.188,0.542 1.563,0.844 0.375,0.302 10 false E 0.938,0.542 1.313,0.844 0.375,0.302 10 false F 0.781,1.813 1.115,2.104 0.333,0.292 10 false A8 5.958,0.552 6.333,0.854 0.375,0.302 10 false A 5.708,0.563 6.083,0.865 0.375,0.302 10 false B 5.333,0.563 5.708,0.865 0.375,0.302 10 false C 5.208,0.563 5.583,0.865 0.375,0.302 10 false D 4.833,0.563 5.208,0.865 0.375,0.302 10 false E 4.594,0.563 4.969,0.865 0.375,0.302 10 false F 1,2.333 1.375,2.604 0.375,0.271 10 false -SL 1.688,2.333 2.094,2.615 0.406,0.281 10 false +SL 4.635,2.333 5.021,2.583 0.385,0.25 10 false -SL 5.344,2.333 5.792,2.594 0.448,0.26 10 false +SL 4.219,1.469 4.573,1.771 0.354,0.302 10 false *a 4.438,1.813 4.771,2.104 0.333,0.292 10 false A8
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A8-2 (+SL) - A8-1 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
a.

Connect the cable to the negative (-) auxiliary battery terminal.

C284128C06
0.698,1.781 1.021,2 0.323,0.219 4.354,1.781 4.677,2 0.323,0.219 1.156,2.313 1.396,1.969 false 1.813,2.313 1.583,1.979 false 4.792,2.323 5.031,1.979 false 5.469,2.313 5.24,1.979 false 0.167,0.083 0.51,0.313 0.344,0.229 10 false *A 3.677,0.104 4.052,0.375 0.375,0.271 10 false *B 0.667,0.542 1,0.833 0.333,0.292 10 false *1 2.646,0.771 3.021,1.073 0.375,0.302 10 false *2 0.573,1.448 0.927,1.75 0.354,0.302 10 false *a 4.313,0.552 4.646,0.844 0.333,0.292 10 false *1 6.302,0.552 6.677,0.854 0.375,0.302 10 false *2 2.302,0.552 2.677,0.854 0.375,0.302 10 false A 2.042,0.552 2.417,0.854 0.375,0.302 10 false B 1.677,0.552 2.052,0.854 0.375,0.302 10 false C 1.552,0.552 1.927,0.854 0.375,0.302 10 false D 1.188,0.542 1.563,0.844 0.375,0.302 10 false E 0.938,0.542 1.313,0.844 0.375,0.302 10 false F 0.781,1.813 1.115,2.104 0.333,0.292 10 false A8 5.958,0.552 6.333,0.854 0.375,0.302 10 false A 5.708,0.563 6.083,0.865 0.375,0.302 10 false B 5.333,0.563 5.708,0.865 0.375,0.302 10 false C 5.208,0.563 5.583,0.865 0.375,0.302 10 false D 4.833,0.563 5.208,0.865 0.375,0.302 10 false E 4.594,0.563 4.969,0.865 0.375,0.302 10 false F 1,2.333 1.375,2.604 0.375,0.271 10 false -SL 1.688,2.333 2.094,2.615 0.406,0.281 10 false +SL 4.635,2.333 5.021,2.583 0.385,0.25 10 false -SL 5.344,2.333 5.792,2.594 0.448,0.26 10 false +SL 4.219,1.469 4.573,1.771 0.354,0.302 10 false *a 4.438,1.813 4.771,2.104 0.333,0.292 10 false A8
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A8-2 (+SL) - Body ground Power switch on (IG) Below 1 V
A8-1 (-SL) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C284128C06
0.698,1.781 1.021,2 0.323,0.219 4.354,1.781 4.677,2 0.323,0.219 1.156,2.313 1.396,1.969 false 1.813,2.313 1.583,1.979 false 4.792,2.323 5.031,1.979 false 5.469,2.313 5.24,1.979 false 0.167,0.083 0.51,0.313 0.344,0.229 10 false *A 3.677,0.104 4.052,0.375 0.375,0.271 10 false *B 0.667,0.542 1,0.833 0.333,0.292 10 false *1 2.646,0.771 3.021,1.073 0.375,0.302 10 false *2 0.573,1.448 0.927,1.75 0.354,0.302 10 false *a 4.313,0.552 4.646,0.844 0.333,0.292 10 false *1 6.302,0.552 6.677,0.854 0.375,0.302 10 false *2 2.302,0.552 2.677,0.854 0.375,0.302 10 false A 2.042,0.552 2.417,0.854 0.375,0.302 10 false B 1.677,0.552 2.052,0.854 0.375,0.302 10 false C 1.552,0.552 1.927,0.854 0.375,0.302 10 false D 1.188,0.542 1.563,0.844 0.375,0.302 10 false E 0.938,0.542 1.313,0.844 0.375,0.302 10 false F 0.781,1.813 1.115,2.104 0.333,0.292 10 false A8 5.958,0.552 6.333,0.854 0.375,0.302 10 false A 5.708,0.563 6.083,0.865 0.375,0.302 10 false B 5.333,0.563 5.708,0.865 0.375,0.302 10 false C 5.208,0.563 5.583,0.865 0.375,0.302 10 false D 4.833,0.563 5.208,0.865 0.375,0.302 10 false E 4.594,0.563 4.969,0.865 0.375,0.302 10 false F 1,2.333 1.375,2.604 0.375,0.271 10 false -SL 1.688,2.333 2.094,2.615 0.406,0.281 10 false +SL 4.635,2.333 5.021,2.583 0.385,0.25 10 false -SL 5.344,2.333 5.792,2.594 0.448,0.26 10 false +SL 4.219,1.469 4.573,1.771 0.354,0.302 10 false *a 4.438,1.813 4.771,2.104 0.333,0.292 10 false A8
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A8-2 (+SL) - Body ground Always 1 MΩ or higher
A8-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT AIRBAG SENSOR LH

NG

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR LH
a.
C279500C02
0.156,0.073 0.552,0.375 0.396,0.302 10 false *A 0.198,2.365 0.573,2.688 0.375,0.323 10 false *B 0.49,0.938 0.833,1.208 0.344,0.271 10 false *1 2.625,3.479 2.948,3.792 0.323,0.313 10 false *2 2.604,1.24 2.948,1.51 0.344,0.271 10 false *2 2.177,0.958 2.521,1.229 0.344,0.271 10 false A 2.021,0.958 2.365,1.229 0.344,0.271 10 false B 1.573,0.958 1.917,1.229 0.344,0.271 10 false C 1.417,0.958 1.76,1.229 0.344,0.271 10 false D 0.969,0.958 1.313,1.229 0.344,0.271 10 false E 0.813,0.958 1.156,1.229 0.344,0.271 10 false F 2.177,3.458 2.521,3.729 0.344,0.271 10 false A 2.021,3.458 2.365,3.729 0.344,0.271 10 false B 1.573,3.458 1.917,3.729 0.344,0.271 10 false C 1.417,3.458 1.76,3.729 0.344,0.271 10 false D 0.969,3.458 1.313,3.729 0.344,0.271 10 false E 0.823,3.458 1.167,3.729 0.344,0.271 10 false F 0.49,3.458 0.833,3.729 0.344,0.271 10 false *1
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly


Connect the connector to the airbag ECU assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348324C02
1.073,1.917 1.417,2.135 0.344,0.219 4.646,1.906 4.99,2.125 0.344,0.219 1.344,0.854 1.344,0.521 false 4.917,0.969 4.917,0.635 false 1.969,0.396 1.969,0.146 1.969,0.146 1.802,0.146 false 5.542,0.51 5.542,0.26 5.542,0.26 5.375,0.26 false 1.51,1.573 1.813,1.823 false 5.052,1.573 5.385,1.823 false 2.271,1.573 1.99,1.823 false 5.875,1.573 5.573,1.823 false 0.083,0.083 0.667,0.333 0.583,0.25 10 false *A 3.667,0.083 4.146,0.323 0.479,0.24 10 false *B 0.604,0.375 1,0.708 0.396,0.333 10 false *1 1.271,0.865 1.667,1.198 0.396,0.333 10 false *3 1,1.333 1.417,1.667 0.417,0.333 10 false *a 4.188,0.49 4.583,0.823 0.396,0.333 10 false *1 2.667,0.604 3.146,1.01 0.479,0.406 10 false *2 6.25,0.49 6.646,0.74 0.396,0.25 10 false *2 4.854,0.979 5.25,1.313 0.396,0.333 10 false *3 1.646,0.073 2.063,0.396 0.417,0.323 10 false *4 5.219,0.188 5.635,0.51 0.417,0.323 10 false *4 4.583,1.333 5,1.667 0.417,0.333 10 false *a 1.125,1.948 1.542,2.281 0.417,0.333 10 false AF5 4.698,1.938 5.115,2.271 0.417,0.333 10 false AF5 1.229,1.5 1.646,1.833 0.417,0.333 10 false +SL 2.333,1.5 2.75,1.833 0.417,0.333 10 false -SL 4.771,1.5 5.188,1.833 0.417,0.333 10 false +SL 5.927,1.5 6.344,1.833 0.417,0.333 10 false -SL 2.354,0.385 2.833,0.792 0.479,0.406 10 false A 2.104,0.385 2.583,0.792 0.479,0.406 10 false B 1.74,0.385 2.219,0.792 0.479,0.406 10 false C 1.479,0.385 1.958,0.792 0.479,0.406 10 false D 1.115,0.385 1.594,0.792 0.479,0.406 10 false E 0.854,0.385 1.333,0.792 0.479,0.406 10 false F 5.938,0.5 6.333,0.75 0.396,0.25 10 false A 5.688,0.5 6.083,0.75 0.396,0.25 10 false B 5.313,0.5 5.708,0.75 0.396,0.25 10 false C 5.063,0.5 5.458,0.75 0.396,0.25 10 false D 4.698,0.5 5.094,0.75 0.396,0.25 10 false E 4.448,0.5 4.844,0.75 0.396,0.25 10 false F
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - Body ground Always 1 MΩ or higher
AF5-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348324C02
1.073,1.917 1.417,2.135 0.344,0.219 4.646,1.906 4.99,2.125 0.344,0.219 1.344,0.854 1.344,0.521 false 4.917,0.969 4.917,0.635 false 1.969,0.396 1.969,0.146 1.969,0.146 1.802,0.146 false 5.542,0.51 5.542,0.26 5.542,0.26 5.375,0.26 false 1.51,1.573 1.813,1.823 false 5.052,1.573 5.385,1.823 false 2.271,1.573 1.99,1.823 false 5.875,1.573 5.573,1.823 false 0.083,0.083 0.667,0.333 0.583,0.25 10 false *A 3.667,0.083 4.146,0.323 0.479,0.24 10 false *B 0.604,0.375 1,0.708 0.396,0.333 10 false *1 1.271,0.865 1.667,1.198 0.396,0.333 10 false *3 1,1.333 1.417,1.667 0.417,0.333 10 false *a 4.188,0.49 4.583,0.823 0.396,0.333 10 false *1 2.667,0.604 3.146,1.01 0.479,0.406 10 false *2 6.25,0.49 6.646,0.74 0.396,0.25 10 false *2 4.854,0.979 5.25,1.313 0.396,0.333 10 false *3 1.646,0.073 2.063,0.396 0.417,0.323 10 false *4 5.219,0.188 5.635,0.51 0.417,0.323 10 false *4 4.583,1.333 5,1.667 0.417,0.333 10 false *a 1.125,1.948 1.542,2.281 0.417,0.333 10 false AF5 4.698,1.938 5.115,2.271 0.417,0.333 10 false AF5 1.229,1.5 1.646,1.833 0.417,0.333 10 false +SL 2.333,1.5 2.75,1.833 0.417,0.333 10 false -SL 4.771,1.5 5.188,1.833 0.417,0.333 10 false +SL 5.927,1.5 6.344,1.833 0.417,0.333 10 false -SL 2.354,0.385 2.833,0.792 0.479,0.406 10 false A 2.104,0.385 2.583,0.792 0.479,0.406 10 false B 1.74,0.385 2.219,0.792 0.479,0.406 10 false C 1.479,0.385 1.958,0.792 0.479,0.406 10 false D 1.115,0.385 1.594,0.792 0.479,0.406 10 false E 0.854,0.385 1.333,0.792 0.479,0.406 10 false F 5.938,0.5 6.333,0.75 0.396,0.25 10 false A 5.688,0.5 6.083,0.75 0.396,0.25 10 false B 5.313,0.5 5.708,0.75 0.396,0.25 10 false C 5.063,0.5 5.458,0.75 0.396,0.25 10 false D 4.698,0.5 5.094,0.75 0.396,0.25 10 false E 4.448,0.5 4.844,0.75 0.396,0.25 10 false F
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)
- -



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - Body ground Power switch on (IG) Below 1 V
AF5-1 (-SL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348324C02
1.073,1.917 1.417,2.135 0.344,0.219 4.646,1.906 4.99,2.125 0.344,0.219 1.344,0.854 1.344,0.521 false 4.917,0.969 4.917,0.635 false 1.969,0.396 1.969,0.146 1.969,0.146 1.802,0.146 false 5.542,0.51 5.542,0.26 5.542,0.26 5.375,0.26 false 1.51,1.573 1.813,1.823 false 5.052,1.573 5.385,1.823 false 2.271,1.573 1.99,1.823 false 5.875,1.573 5.573,1.823 false 0.083,0.083 0.667,0.333 0.583,0.25 10 false *A 3.667,0.083 4.146,0.323 0.479,0.24 10 false *B 0.604,0.375 1,0.708 0.396,0.333 10 false *1 1.271,0.865 1.667,1.198 0.396,0.333 10 false *3 1,1.333 1.417,1.667 0.417,0.333 10 false *a 4.188,0.49 4.583,0.823 0.396,0.333 10 false *1 2.667,0.604 3.146,1.01 0.479,0.406 10 false *2 6.25,0.49 6.646,0.74 0.396,0.25 10 false *2 4.854,0.979 5.25,1.313 0.396,0.333 10 false *3 1.646,0.073 2.063,0.396 0.417,0.323 10 false *4 5.219,0.188 5.635,0.51 0.417,0.323 10 false *4 4.583,1.333 5,1.667 0.417,0.333 10 false *a 1.125,1.948 1.542,2.281 0.417,0.333 10 false AF5 4.698,1.938 5.115,2.271 0.417,0.333 10 false AF5 1.229,1.5 1.646,1.833 0.417,0.333 10 false +SL 2.333,1.5 2.75,1.833 0.417,0.333 10 false -SL 4.771,1.5 5.188,1.833 0.417,0.333 10 false +SL 5.927,1.5 6.344,1.833 0.417,0.333 10 false -SL 2.354,0.385 2.833,0.792 0.479,0.406 10 false A 2.104,0.385 2.583,0.792 0.479,0.406 10 false B 1.74,0.385 2.219,0.792 0.479,0.406 10 false C 1.479,0.385 1.958,0.792 0.479,0.406 10 false D 1.115,0.385 1.594,0.792 0.479,0.406 10 false E 0.854,0.385 1.333,0.792 0.479,0.406 10 false F 5.938,0.5 6.333,0.75 0.396,0.25 10 false A 5.688,0.5 6.083,0.75 0.396,0.25 10 false B 5.313,0.5 5.708,0.75 0.396,0.25 10 false C 5.063,0.5 5.458,0.75 0.396,0.25 10 false D 4.698,0.5 5.094,0.75 0.396,0.25 10 false E 4.448,0.5 4.844,0.75 0.396,0.25 10 false F
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - AF5-1 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348387C01
1.104,0.49 1.448,0.719 0.344,0.229 4.698,0.49 5.042,0.719 0.344,0.229 0.781,3.042 1.125,3.271 0.344,0.229 4.354,3.073 4.698,3.302 0.344,0.229 2.344,1.198 2.344,1.031 false 5.927,1.198 5.927,1.031 false 1.365,2.083 1.365,1.833 false 1.979,1.708 1.979,1.5 1.979,1.5 1.813,1.5 false 5.563,1.896 5.563,1.688 5.563,1.688 5.396,1.688 false 4.948,2.271 4.948,2.021 false 2.042,1.063 2.26,0.802 false 2.635,1.063 2.417,0.813 false 5.615,1.063 5.833,0.802 false 6.198,1.063 6.01,0.813 false 1.479,2.958 1.24,2.656 false 1.615,2.958 1.844,2.656 false 5.198,2.969 5.427,2.667 false 5.052,2.958 4.813,2.656 false 0.198,0.083 0.698,0.417 0.5,0.333 10 false *A 3.781,0.083 4.198,0.417 0.417,0.333 10 false *B 0.635,1.698 1.031,2.104 0.396,0.406 10 false *1 2.677,1.917 3.073,2.24 0.396,0.323 10 false *2 1.292,2.104 1.708,2.427 0.417,0.323 10 false *3 1.656,1.417 2.135,1.823 0.479,0.406 10 false *4 5.865,1.208 6.344,1.542 0.479,0.333 10 false *5 1.083,0.25 1.5,0.583 0.417,0.333 10 false *a 4.26,2.552 4.677,2.896 0.417,0.344 10 false *b 6.25,1.875 6.646,2.198 0.396,0.323 10 false *2 4.219,1.885 4.615,2.292 0.396,0.406 10 false *1 4.885,2.281 5.302,2.604 0.417,0.323 10 false *3 5.25,1.615 5.729,2.021 0.479,0.406 10 false *4 4.667,0.25 5.083,0.583 0.417,0.333 10 false *a 0.667,2.552 1.083,2.896 0.417,0.344 10 false *b 2.375,1.708 2.771,2.031 0.396,0.323 10 false A 2.125,1.708 2.521,2.031 0.396,0.323 10 false B 1.75,1.708 2.146,2.031 0.396,0.323 10 false C 1.5,1.708 1.896,2.031 0.396,0.323 10 false D 1.135,1.708 1.531,2.031 0.396,0.323 10 false E 0.885,1.708 1.281,2.031 0.396,0.323 10 false F 5.958,1.885 6.354,2.208 0.396,0.323 10 false A 5.708,1.885 6.104,2.208 0.396,0.323 10 false B 5.333,1.885 5.729,2.208 0.396,0.323 10 false C 5.083,1.885 5.479,2.208 0.396,0.323 10 false D 4.719,1.885 5.115,2.208 0.396,0.323 10 false E 4.469,1.885 4.865,2.208 0.396,0.323 10 false F 2.271,1.208 2.75,1.542 0.479,0.333 10 false *5 1.167,0.521 1.563,0.927 0.396,0.406 10 false F56 4.76,0.521 5.156,0.927 0.396,0.406 10 false F56 2.667,1 3.063,1.406 0.396,0.406 10 false +SL 1.802,1 2.198,1.406 0.396,0.406 10 false -SL 6.229,1 6.625,1.406 0.396,0.406 10 false +SL 5.365,1 5.76,1.406 0.396,0.406 10 false -SL 0.833,3.073 1.229,3.479 0.396,0.406 10 false AF5 4.406,3.104 4.802,3.51 0.396,0.406 10 false AF5 0.969,2.583 1.365,2.99 0.396,0.406 10 false +SL 1.896,2.583 2.292,2.99 0.396,0.406 10 false -SL 4.531,2.583 4.927,2.99 0.396,0.406 10 false +SL 5.49,2.583 5.885,2.99 0.396,0.406 10 false -SL
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Service Wire - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - AF5-1 (-SL) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE