Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the power switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag ECU assembly, combination meter assembly or wire harness connected to the airbag ECU assembly or combination meter assembly, the SRS warning light comes on.

When terminals TC and CG of the DLC3 are connected, DTCs are displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.

When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag ECU assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag ECU assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C263701E50
0.177,1.823 1.656,2.375 1.479,0.552 10 false from Auxiliary Battery 4.906,0.729 5.781,0.979 0.875,0.25 10 false A/BAG-IG2 2.094,1.417 3.135,1.708 1.042,0.292 10 false METER-IG2 1.958,1.969 3.25,2.333 1.292,0.365 10 false ECU-DCC NO. 2 3.094,2.365 3.396,2.635 0.302,0.271 10 false ES 2.854,1.719 3.125,2.01 0.271,0.292 10 false 22 2.865,1.177 3.188,1.427 0.323,0.25 10 false 21 5.802,1.115 6.208,1.385 0.406,0.271 10 false 13 4.094,1.125 4.417,1.375 0.323,0.25 10 false 26 2.854,2.271 3.25,2.594 0.396,0.323 10 false 28 6.052,0.594 6.427,0.906 0.375,0.313 10 false IG2 3.615,1.26 4.302,1.583 0.688,0.323 10 false CANH 3.635,1.823 4.25,2.177 0.615,0.354 10 false CANL 6.063,2.365 6.354,2.625 0.292,0.26 10 false E1 6.063,2.875 6.354,3.125 0.292,0.25 10 false E2 6.01,3.615 6.521,3.906 0.51,0.292 10 false F56 3.042,3.604 3.448,3.854 0.406,0.25 10 false F6 5.99,3.771 6.844,4.271 0.854,0.5 10 false Airbag ECU Assembly 3.042,3.771 4.24,4.333 1.198,0.563 10 false Combination Meter Assembly 5.802,1.677 6.313,1.958 0.51,0.281 10 false 22 6.052,1.26 6.583,1.5 0.531,0.24 10 false CANH 6.052,1.802 6.552,2.021 0.5,0.219 10 false CANL 5.802,0.49 6.25,0.781 0.448,0.292 10 false 21 5.813,2.271 6.208,2.521 0.396,0.25 10 false 25 5.813,2.781 6.104,2.979 0.292,0.198 10 false 26 4.094,1.677 4.5,2.031 0.406,0.354 10 false 27 3.104,1.813 3.406,2.031 0.302,0.219 10 false B 3.104,1.26 3.479,1.49 0.375,0.229 10 false IG+ 0.74,4.177 2.51,4.479 1.771,0.302 10 false : CAN Communication Line 2.938,0.573 4.448,0.885 1.51,0.313 10 false from IG2-NO. 2 Relay 0.156,1.24 1.865,1.615 1.708,0.375 10 false from IG2-NO. 2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK SRS WARNING LIGHT OPERATION
a.

Turn the power switch on (IG) and check the SRS warning light condition.

HINT:

The primary check is performed for approximately 6 seconds after the power switch is turned on (IG).



Result:
Result Proceed to
After the primary check period, the SRS warning light remains on. A
After the primary check period, the SRS warning light goes off and comes on again. B



A

2.CHECK AUXILIARY BATTERY VOLTAGE

B

6.CHECK CAN COMMUNICATION SYSTEM
2.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the power switch off.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR

NG

INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY

3.CHECK CONNECTOR
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag ECU assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag ECU assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

4.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)
a.
C126715C41
0.427,0.833 0.813,1.083 0.385,0.25 1.292,1.302 0.854,1.708 false 1.656,1.313 1.219,1.708 false 1.75,1.313 2.188,1.719 false 0.115,0.073 0.396,0.438 0.281,0.365 10 false *a 0.51,0.885 0.885,1.208 0.375,0.323 10 false F56 0.729,1.719 1.135,2.073 0.406,0.354 10 false IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 false E1 2.146,1.729 2.521,2 0.375,0.271 10 false E2
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F56-21 (IG2) - Body ground Power switch on (IG) 8 to 16 V



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F56-25 (E1) - Body ground Always Below 1 Ω
F56-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK SRS WARNING LIGHT

NG

REPLACE WIRE HARNESS

5.CHECK SRS WARNING LIGHT
a.

Turn the power switch on (IG) and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the power switch is turned on (IG).



Result:
Proceed to
OK
NG



OK

NG

6.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check in CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

7.CHECK AUXILIARY BATTERY VOLTAGE

NG

7.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the power switch off.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR

NG

INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY

8.CHECK CONNECTOR
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag ECU assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag ECU assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

9.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)
a.
C126715C41
0.427,0.833 0.813,1.083 0.385,0.25 1.292,1.302 0.854,1.708 false 1.656,1.313 1.219,1.708 false 1.75,1.313 2.188,1.719 false 0.115,0.073 0.396,0.438 0.281,0.365 10 false *a 0.51,0.885 0.885,1.208 0.375,0.323 10 false F56 0.729,1.719 1.135,2.073 0.406,0.354 10 false IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 false E1 2.146,1.729 2.521,2 0.375,0.271 10 false E2
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F56-21 (IG2) - Body ground Power switch on (IG) 8 to 16 V



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F56-25 (E1) - Body ground Always Below 1 Ω
F56-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR

NG

REPLACE WIRE HARNESS

10.CHECK CONNECTOR
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C241761C34
0.25,0.417 0.667,0.667 0.417,0.25 0.479,1.917 0.885,1.719 false 1.708,1.719 2.156,0.667 2.156,0.667 2.646,0.667 false 0.427,1.323 1,1.708 false 0.083,0.052 0.51,0.406 0.427,0.354 10 false *a 0.24,1.854 0.573,2.073 0.333,0.219 10 false IG+ 0.313,1.24 0.573,1.458 0.26,0.219 10 false B 2.698,0.594 3,0.865 0.302,0.271 10 false ES 0.385,0.458 0.76,0.74 0.375,0.281 10 false F6
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V
F6-22 (B) - Body ground Power switch off 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-28 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

12.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG) and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the power switch is turned on (IG).



Result:
Proceed to
OK
NG



OK

NG