Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0225119 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN
·

Errors in LIN communication between ECUs or an open or short in communication lines.

·

LIN communication error detected by the certification ECU (smart key ECU assembly) 3 times in a row.


·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU

·

ID code box (immobiliser code ECU)

·

Wire harness or connector

·

ECU-B NO. 1 fuse

·

ECU-B NO. 2 fuse

·

AM2 fuse



WIRING DIAGRAM

B439128E01
1.396,2.146 3.219,2.521 1.823,0.375 10 false Certification ECU (Smart Key ECU Assembly) 1.49,4.292 3.073,4.719 1.583,0.427 10 false ID Code Box (Immobiliser Code ECU) 1.5,4.115 1.875,4.375 0.375,0.26 10 false F19 0.948,5.313 3.479,5.573 2.531,0.26 10 false : LIN Communication Line 3.792,2.552 6.323,2.813 2.531,0.26 10 false Hybrid Vehicle Control ECU 4.188,0.208 6.719,0.469 2.531,0.26 10 false from Auxiliary Battery 0.594,1.323 0.958,1.563 0.365,0.24 10 false AM2 1.719,1.177 2.083,1.417 0.365,0.24 10 false +B 1.719,1.729 2.083,1.969 0.365,0.24 10 false E 1.552,1.094 1.917,1.333 0.365,0.24 10 false 4 1.49,1.615 1.854,1.854 0.365,0.24 10 false 18 2.688,1.417 3.052,1.656 0.365,0.24 10 false LIN 2.969,1.271 3.333,1.51 0.365,0.24 10 false 13 3.813,1.417 4.177,1.656 0.365,0.24 10 false F3 3.823,1.229 4.188,1.469 0.365,0.24 10 false 31 4.094,1.406 4.458,1.646 0.365,0.24 10 false LIN 4.948,1.167 5.313,1.406 0.365,0.24 10 false BATT 5.104,1.667 5.469,1.906 0.365,0.24 10 false E1 5.031,2.188 5.396,2.427 0.365,0.24 10 false E12 5.417,1.188 5.781,1.427 0.365,0.24 10 false F3 5.406,1.677 5.771,1.917 0.365,0.24 10 false F3 5.417,2.198 5.781,2.438 0.365,0.24 10 false F2 5.865,1.354 6.896,1.552 1.031,0.198 10 false ECU-B NO. 2 5.417,1 5.781,1.24 0.365,0.24 10 false 27 5.469,1.479 5.833,1.719 0.365,0.24 10 false 3 5.406,2.01 5.771,2.25 0.365,0.24 10 false 34 2.615,3.531 2.979,3.771 0.365,0.24 10 false LIN1 1.708,3.729 2.073,3.969 0.365,0.24 10 false GND 1.719,3.229 2.083,3.469 0.365,0.24 10 false +B 0.51,3.396 1.542,3.594 1.031,0.198 10 false ECU-B NO. 1 1.542,3.146 1.906,3.385 0.365,0.24 10 false 1 1.563,3.604 1.927,3.844 0.365,0.24 10 false 5 2.958,3.396 3.323,3.635 0.365,0.24 10 false 2 1.396,2 1.76,2.24 0.365,0.24 10 false F1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), hybrid vehicle control ECU or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

Before performing the inspection, check that DTC B2786, B2789 or B278C is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F3 hybrid vehicle control ECU connector.


c.

Disconnect the F19 ID code box (immobiliser code ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on(IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
F1-13 (LIN) - F3-31 (LIN) Power switch off Below 1 Ω
F1-13 (LIN) - F19-2 (LIN1) Power switch off Below 1 Ω
F1-13 (LIN) or F19-2 (LIN1) - Body ground Power switch off 10 kΩ or higher
F3-31 (LIN) or F19-2 (LIN1) - Body ground Power switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT (HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC OUTPUT (HYBRID VEHICLE CONTROL ECU)
a.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F19 ID code box (immobiliser code ECU) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

d.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

3.CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))

B

3.CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))
a.

Reconnect the F3 hybrid vehicle control ECU connector.


b.

Disconnect the F19 ID code box (immobiliser code ECU) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

d.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)