Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID VEHICLE CONTROL ECU
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0244764 HYBRID VEHICLE CONTROL ECU A

HYBRID / BATTERY CONTROL  HYBRID VEHICLE CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle control ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of hybrid vehicle control ECU Perform code registration (Immobiliser system)
·

Entry and start system

·

Wireless door lock control system

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
Clear DTCs (Vehicle proximity notification system)*2 Vehicle proximity notification system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

*2: w/ Vehicle Proximity Notification System

PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55607 3.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 4.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82877 5.REMOVE ECU INTEGRATION BOX RH (for LHD)

a.

Disconnect each connector.


b.
A371716C03
0.375,1.365 0.375,0.979 0.375,0.979 0.552,0.885 false 0.979,2.177 1.063,1.896 1.063,1.896 1.24,1.896 false 0.344,1.396 0.656,1.594 0.313,0.198 10 false *a 1.292,1.823 1.604,2.021 0.313,0.198 10 false *a
*a Lock Lever


Move each lock lever as shown in the illustration and disconnect the 3 hybrid vehicle control ECU connectors.


c.
A371719

Disengage the 3 clamps.


d.
A371718

Remove the bolt, 2 nuts and ECU integration box RH.


Hide 89981 6.REMOVE HYBRID VEHICLE CONTROL ECU (for LHD)

a.
A371720

Disengage the 2 claws and remove the hybrid vehicle control ECU as shown in the illustration.

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




Hide 82878 7.REMOVE ECU INTEGRATION BOX LH (for RHD)

a.

Disconnect each connector.


b.
A371723C02
0.417,1.458 0.417,1 0.417,1 0.573,0.896 false 1,2.208 1.083,1.958 1.083,1.958 1.281,1.958 false 0.396,1.521 0.708,1.719 0.313,0.198 10 false *a 1.344,1.906 1.656,2.104 0.313,0.198 10 false *a
*a Lock Lever


Move each lock lever as shown in the illustration and disconnect the 3 hybrid vehicle control ECU connectors.


c.
A371726

Remove the bolt, nut and ECU integration box LH.


Hide 89981 8.REMOVE HYBRID VEHICLE CONTROL ECU (for RHD)

a.
A371725

Disengage the 2 claws and remove the hybrid vehicle control ECU as shown in the illustration.

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.