Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0225119 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and hybrid vehicle control ECU stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2786 No Response from Steering Lock ECU No communication between hybrid vehicle control ECU and certification ECU (smart key ECU assembly) for 10 seconds or more.
·

Hybrid vehicle control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector

·

ECU-B NO. 2 fuse



WIRING DIAGRAM

B419483E03
4.219,1.458 4.677,1.656 0.458,0.198 10 false LIN 1.844,1.469 2.302,1.667 0.458,0.198 10 false LIN 0.667,3.448 2.365,3.677 1.698,0.229 10 false : LIN Communication line 1.021,2.385 1.479,2.583 0.458,0.198 10 false F1 1.021,2.552 2.542,3.01 1.521,0.458 10 false Certification ECU (Smart Key ECU Assembly) 3.875,2.448 5.656,2.698 1.781,0.25 10 false Hybrid Vehicle Control ECU 2.146,1.313 2.604,1.51 0.458,0.198 10 false 13 3.917,1.313 4.375,1.51 0.458,0.198 10 false 31 4.896,1.083 5.354,1.281 0.458,0.198 10 false +B 5.229,0.896 5.688,1.094 0.458,0.198 10 false 27 4.906,1.51 5.365,1.708 0.458,0.198 10 false E1 4.854,1.969 5.313,2.167 0.458,0.198 10 false E12 5.208,1.781 5.667,1.979 0.458,0.198 10 false 34 5.479,1.219 6.323,1.427 0.844,0.208 10 false ECU-B NO. 2 4.333,0.385 5.802,0.594 1.469,0.208 10 false from Auxiliary Battery 5.25,1.333 5.708,1.531 0.458,0.198 10 false 3 3.948,1.479 4.406,1.677 0.458,0.198 10 false F3 5.229,1.073 5.688,1.271 0.458,0.198 10 false F3 5.229,1.51 5.688,1.708 0.458,0.198 10 false F3 5.229,1.958 5.688,2.156 0.458,0.198 10 false F2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or hybrid vehicle control ECU, refer to Service Bulletin.

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F3 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on(IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
F1-13 (LIN) - F3-31 (LIN) Power switch off Below 1 Ω
F1-13 (LIN) or F3-31 (LIN) - Body ground Power switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AUXILIARY BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-27 (+B) - F3-3 (E1) or F2-34 (E12) Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-3 (E1) - Body ground Always Below 1 Ω
F2-34 (E12) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE HYBRID VEHICLE CONTROL ECU
a.

Temporarily replace the hybrid vehicle control ECU with a new one.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.REGISTER ECU CODE REGISTRATION
4.REGISTER ECU CODE REGISTRATION
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B2786 is not output.



Result:
Proceed to
OK
NG



OK

END (HYBRID VEHICLE CONTROL ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)