Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0225119 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2321 Driver Side Door ECU Communication Stop No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for driver door)

·

Main body ECU (multiplex network body ECU)

·

Multiplex network master switch assembly

·

Wire harness or connector

·

POWER fuse



WIRING DIAGRAM

B443245E01
4.292,3.396 5.979,3.594 1.688,0.198 10 false *1: for LHD 5.271,3.396 6.958,3.594 1.688,0.198 10 false *2: for RHD 0.542,3.448 2.573,3.656 2.031,0.208 10 false : LIN Communication Line 4.813,0.094 6.5,0.292 1.688,0.198 10 false from Auxiliary Battery 0.073,2.25 1.719,2.698 1.646,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 1.823,1.99 2.896,2.646 1.073,0.656 10 false Instrument Panel Junction Block Assembly 3.042,2.396 4.688,2.844 1.646,0.448 10 false Multiplex Network Master Switch Assembly 4.906,2.344 6.854,2.823 1.948,0.479 10 false Power Window Regulator Motor Assembly (for Driver Door) 4.906,2.177 6.594,2.375 1.688,0.198 10 false J2*1, I2*2 3.052,2.219 4.74,2.417 1.688,0.198 10 false J7 1.813,1.833 3.5,2.031 1.688,0.198 10 false 3H 0.083,2.083 1.771,2.281 1.688,0.198 10 false MB 1.104,1.198 2.792,1.396 1.688,0.198 10 false LIN2 1.479,1.052 3.167,1.25 1.688,0.198 10 false 16 2.448,1.052 4.135,1.25 1.688,0.198 10 false 25 3.146,1.042 4.833,1.24 1.688,0.198 10 false 17 3.396,1.042 5.083,1.24 1.688,0.198 10 false LIN1 3.969,1.042 5.656,1.24 1.688,0.198 10 false LIN2 4.344,1.042 6.031,1.24 1.688,0.198 10 false 16 4.99,1.042 6.677,1.24 1.688,0.198 10 false 9 5.167,1.198 6.854,1.396 1.688,0.198 10 false LIN 5.917,0.948 6.635,1.167 0.719,0.219 10 false B 5.729,1.594 6.448,1.813 0.719,0.219 10 false GND 6.115,0.813 7.052,1 0.938,0.188 10 false 2 6.115,1.458 7.052,1.646 0.938,0.188 10 false 1 6.313,1.094 7.031,1.323 0.719,0.229 10 false POWER

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B2321 is output A
DTC B1206 and B2321 are output simultaneously B


HINT:

When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.



A

2.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

2.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.
B365181C01
1.156,1.854 1.49,1.854 1.49,1.854 1.49,1.354 false 2.083,1.854 1.667,1.854 1.667,1.854 1.667,1.354 false 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 0.844,1.781 1.458,1.979 0.615,0.198 10 false LIN1 2.146,1.771 2.76,1.969 0.615,0.198 10 false LIN2
*a Component without harness connected
(Multiplex Network Master Switch Assembly)


Remove the multiplex network master switch assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (LIN2) - 17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
a.

for LHD

i.

Disconnect the J2 power window regulator motor assembly (for driver door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
J7-16 (LIN2) - J2-9 (LIN) Power Switch off Below 1 Ω
J7-16 (LIN2) or J2-9 (LIN) - Body ground Power Switch off 10 kΩ or higher




b.

for RHD

i.

Disconnect the I2 power window regulator motor assembly (for driver door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
J7-16 (LIN2) - I2-9 (LIN) Power Switch off Below 1 Ω
J7-16 (LIN2) or I2-9 (LIN) - Body ground Power Switch off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - AUXILIARY BATTERY, BODY GROUND)
a.

for LHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J2-2 (B) - J2-1 (GND) Power Switch off 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-1 (GND) - Body ground Always Below 1 Ω




b.

for RHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I2-2 (B) - I2-1 (GND) Power Switch off 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

5.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)
a.

Replace the power window regulator motor assembly (for driver door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2321 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)