Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0227085 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch assembly signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the hybrid vehicle control ECU through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the power switch is on (IG) and the cruise control system is operating, the voltage of the STP and ST1- terminals of the hybrid vehicle control ECU are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A378408E02
0.083,0.49 3.448,0.688 3.365,0.198 10 false from Auxiliary Battery 0.104,0.979 3.469,1.177 3.365,0.198 10 false from IG2 NO. 2 Relay 1.948,0.698 5.313,0.896 3.365,0.198 10 false J/B-B 2.823,0.708 6.188,0.906 3.365,0.198 10 false STOP 2.146,1.208 5.51,1.406 3.365,0.198 10 false ECU-IG2 NO. 3 3.573,0.51 6.938,0.708 3.365,0.198 10 false B 3.573,1.01 6.938,1.208 3.365,0.198 10 false B 3.573,1.51 6.938,1.708 3.365,0.198 10 false GND 4.146,0.375 4.521,0.656 0.375,0.281 10 false L 4.167,1.167 4.542,1.448 0.375,0.281 10 false L 5.281,0.396 5.656,0.677 0.375,0.281 10 false A50 5.333,1.177 5.708,1.458 0.375,0.281 10 false F2 5.365,0.167 5.74,0.448 0.375,0.281 10 false 7 5.323,0.958 5.698,1.24 0.375,0.281 10 false 28 5.667,0.271 6.042,0.552 0.375,0.281 10 false STP 5.667,1.073 6.042,1.354 0.375,0.281 10 false ST1- 3.177,3.104 5.208,3.49 2.031,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.198,2.917 3.573,3.198 0.375,0.281 10 false A41 5.385,2.938 5.76,3.219 0.375,0.281 10 false M59 5.396,3.094 6.906,3.427 1.51,0.333 10 false Certification ECU (Smart Key ECU Assembly) 5.74,2.719 6.115,3 0.375,0.281 10 false STP1 3.99,2.521 4.365,2.802 0.375,0.281 10 false STP 3.917,2.719 4.292,3 0.375,0.281 10 false STP2 0.104,3.198 4.385,3.396 4.281,0.198 10 false *1: w/ Canister Pump Module 0.104,3.448 4.385,3.646 4.281,0.198 10 false *2: w/o Canister Pump Module 4.333,2.406 4.948,2.604 0.615,0.198 10 false 12*1 2.896,2.031 4.719,2.24 1.823,0.208 10 false Stop Light Switch Assembly 2.906,1.875 3.854,2.052 0.948,0.177 10 false A46*1, A47*2 4.354,2.625 4.969,2.823 0.615,0.198 10 false 37*2 5.5,2.615 6.115,2.813 0.615,0.198 10 false 25 4.333,0.125 5.281,0.302 0.948,0.177 10 false 2*1 4.333,0.281 5.281,0.458 0.948,0.177 10 false 3*2 4.323,0.917 5.271,1.094 0.948,0.177 10 false 4*1 4.323,1.083 5.271,1.26 0.948,0.177 10 false 5*2 3.271,0.208 4.219,0.385 0.948,0.177 10 false 1*1 3.271,0.396 4.219,0.573 0.948,0.177 10 false 7*2 3.281,0.729 4.229,0.906 0.948,0.177 10 false 5*1 3.281,0.896 4.229,1.073 0.948,0.177 10 false 6*2 3.281,1.219 4.229,1.396 0.948,0.177 10 false 3*1 3.281,1.417 4.229,1.594 0.948,0.177 10 false 2*2 5.625,1.885 6.521,2.25 0.896,0.365 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:

After performing repairs on the vehicle, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG).

2.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).

3.

Depress the brake pedal for 0.5 seconds or more.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

w/ Canister Pump Module:

i.
E239037C49
1.51,0.26 1.896,0.51 0.385,0.25 1.479,1.948 1.625,1.948 1.625,1.948 1.708,1.448 true 0.938,1.781 1.094,1.781 1.094,1.781 1.323,1.438 true 2.427,1.781 2.26,1.781 2.26,1.781 2.073,1.438 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 0.813,1.698 0.969,1.896 0.156,0.198 10 false B 2.469,1.698 2.625,1.896 0.156,0.198 10 false B 1.156,1.875 1.531,2.083 0.375,0.208 10 false GND 1.583,0.302 1.906,0.5 0.323,0.198 10 false A46
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A46 stop light switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-3 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A46-1 (B) - Body ground Always 11 to 14 V
A46-5 (B) - Body ground Power switch on (IG) 11 to 14 V
A46-5 (B) - Body ground Power switch off Below 1 V




b.

w/o Canister Pump Module:

i.
E233306C49
1.521,0.26 1.854,0.479 0.333,0.219 1.292,1.167 1.042,1.854 true 2.281,1.115 2.656,0.958 true 1.958,1.177 1.708,1.865 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.573,0.302 2,0.521 0.427,0.219 10 false A47 2.708,0.875 2.875,1.042 0.167,0.167 10 false B 0.906,1.896 1.417,2.135 0.51,0.24 10 false GND 1.667,1.896 1.833,2.063 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A47 stop light switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-2 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-7 (B) - Body ground Always 11 to 14 V
A47-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A47-6 (B) - Body ground Power switch off Below 1 V




Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A50 and F2 hybrid vehicle control ECU connector.


b.

Disconnect the A46 stop light switch assembly connector (w/ Canister Pump Module).


c.

Disconnect the A47 stop light switch assembly connector (w/o Canister Pump Module).


d.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


e.

Disconnect the M59 certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (w/ Canister Pump Module):
Tester Connection Condition Specified Condition
F2-28 (ST1-) - A46-4 (L) Always Below 1 Ω
A50-7 (STP) - A46-2 (L) Always Below 1 Ω
F2-28 (ST1-) or A46-4 (L) - Body ground Always 10 kΩ or higher
A50-7 (STP) or A46-2 (L) - Body ground Always 10 kΩ or higher


Standard Resistance (w/o Canister Pump Module):
Tester Connection Condition Specified Condition
F2-28 (ST1-) - A47-5 (L) Always Below 1 Ω
A50-7 (STP) - A47-3 (L) Always Below 1 Ω
F2-28 (ST1-) or A47-5 (L) - Body ground Always 10 kΩ or higher
A50-7 (STP) or A47-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR