Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230369 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62180A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:
B417759C02
0,0 0,0 false
V100155

Deployment Side


When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B432335C01
0.906,0.667 1.156,0.344 1.156,0.344 1.375,0.344 true 1.656,2.26 1.906,1.938 1.906,1.938 2.125,1.938 true 0.969,2.021 1.229,2.021 1.229,2.021 1.521,2.365 true 2.146,1.833 2.333,2.042 0.188,0.208 10 true *a 1.406,0.26 1.719,0.417 0.313,0.156 10 false *b 0.792,1.927 0.979,2.125 0.188,0.198 10 true *c
*a Airbag Connector
*b Airbag Connector Lock
*c Protective Tape


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.

Using needle nose pliers, remove the 6 pins from the 6 clips (A).

NOTICE:

Do not damage the pins.


B434295C01
3.635,2.781 4.052,2.781 false 2.135,3.313 2.354,3.313 false 2.063,2.948 2.281,2.948 false 3.49,3.417 3.729,3.417 3.729,3.417 3.969,3.188 true 5.406,0.938 6.948,0.938 6.948,0.938 6.948,2.531 true 5.906,1.896 5.906,0.938 true 1.385,0.135 1.604,0.354 0.219,0.219 10 true *A 2.313,2.865 2.51,3.094 0.198,0.229 10 false *1 3.323,3.333 3.542,3.531 0.219,0.198 10 false *2 3.469,2.698 3.677,2.917 0.208,0.219 10 false *a 1.333,1.375 1.51,1.563 0.177,0.188 10 true *b 5.24,0.844 5.458,1.063 0.219,0.219 10 false *c 0,1.094 0.156,1.25 0.156,0.156 10 false - 3.094,1.198 3.271,1.385 0.177,0.188 10 true *b 5.583,1.51 5.76,1.698 0.177,0.188 10 true *b 2.375,3.229 2.688,3.385 0.313,0.156 10 false *a
*A w/o Occupant Classification System - -
*1 Pin *2 Spacer
*a Clip (A) *b Clip (B)
*c Spacer Location - -



e.

Using 2 screwdrivers, disengage the 2 claws of each clip (A) and separate the 6 clips (A) from the vehicle body as shown in the illustration.

HINT:

Separate the 6 clips (A) and curtain shield airbag assembly from the vehicle body as a unit.



f.

Disengage the 3 clips (B).


g.

While holding the curtain shield airbag assembly, remove the 3 bolts and curtain shield airbag assembly.


h.

Remove the 6 clips (A) and 2 spacers from the curtain shield airbag assembly.