Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM3210E _58 Vehicle Interior _047504 INTERIOR PANELS / TRIM _0242015 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 64910J 1.REMOVE TONNEAU COVER ASSEMBLY

a.

Remove the tonneau cover assembly.


Hide 58415E 2.REMOVE REAR NO. 1 FLOOR BOARD

a.

Remove the rear No. 1 floor board.


Hide 58432D 3.REMOVE DECK BOARD RETAINER

a.
B431726C02
0,0 0,0 false
V113147

Remove in this Direction


for LH Side:

i.

Disengage the clip and guide to remove the deck board retainer as shown in the illustration.



b.
B439095C03
0,0 0,0 false
V113147

Remove in this Direction


for RH Side:

i.

Disengage the clip and guide to remove the deck board retainer as shown in the illustration.



Hide 64997 4.REMOVE DECK FLOOR BOX LH (w/o Spare Tire)

a.
B431728C02
2.552,1.073 2.865,0.969 true 2.896,0.865 3.146,1.052 0.25,0.188 10 true *a
*a Protective Tape
V113147

Turn in this Direction
V113148

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.


Hide 64995 5.REMOVE DECK FLOOR BOX RH (w/o Spare Tire)

a.
B437805C02
0.792,1.115 1.156,0.625 true 1.167,0.5 1.396,0.698 0.229,0.198 10 true *a
*a Protective Tape
V113147

Turn in this Direction
V113148

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.


Hide 64993 6.REMOVE REAR DECK FLOOR BOX (w/ Compact Spare Tire)

a.

Remove the rear deck floor box.


Hide 64997 7.REMOVE DECK FLOOR BOX LH (w/ Compact Spare Tire)

a.
B437807C02
2.76,1.198 3.073,0.813 true 3.083,0.698 3.292,0.906 0.208,0.208 10 true *a
*a Protective Tape
V113147

Turn in this Direction
V113148

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.


Hide 64995 8.REMOVE DECK FLOOR BOX RH (w/ Compact Spare Tire)

a.
B437808C02
0.708,1.438 1.219,1.125 true 1.229,1.01 1.448,1.208 0.219,0.198 10 true *a
*a Protective Tape
V113147

Turn in this Direction
V113148

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.


Hide 64995 9.REMOVE DECK FLOOR BOX RH (w/ Full Size Spare Tire)

a.
B433804C01
0.635,1.51 1.135,1.927 true 1.156,1.823 1.385,2.031 0.229,0.208 10 true *a
*a Protective Tape
V113147

Turn in this Direction
V113148

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.


Hide 64997 10.REMOVE DECK FLOOR BOX LH (w/ Full Size Spare Tire)

a.
B437806C01
2.75,1.208 3.115,0.958 true 3.125,0.875 3.354,1.052 0.229,0.177 10 true *a
*a Protective Tape
V113147

Turn in this Direction
V113148

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.


Hide 64718D 11.REMOVE DECK TRIM SERVICE HOLE COVER

Hide 58460D 12.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)

a.
B431731

Remove the 2 bolts.


b.

Disengage the 2 guides to remove the 2 luggage hold belt striker assemblies.


Hide 64716D 13.REMOVE REAR DECK TRIM COVER

a.
B431732C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 clips and 2 guides to remove the rear deck trim cover as shown in the illustration.


Hide 67914 14.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B431735C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw as shown in the illustration.

HINT:

Use the same procedure for the front side and rear side.



b.
B431738C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 claws and 2 guides to remove the front door scuff plate LH as shown in the illustration.


Hide 62112 15.REMOVE COWL SIDE TRIM BOARD LH

a.
B431742C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the 2 clips to remove the cowl side trim board LH as shown in the illustration.


Hide 62312B 16.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62212 17.REMOVE FRONT PILLAR GARNISH LH

a.
B431745C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front pillar garnish LH as shown in the illustration.


b.
B431747C01
2.021,1.667 2.021,1.448 false 1.969,1.667 2.281,1.823 0.313,0.156 10 false *1
*1 Front Pillar Garnish Clip
V113146

Place Hand Here
V113147

Remove in this Direction


Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

HINT:

Let the front pillar garnish LH hang from the front pillar garnish clip.



c.
B431751C01
2.479,0.906 2.479,0.635 false 2.427,0.917 2.667,1.083 0.24,0.167 10 false *1
*1 Front Pillar Garnish Clip
V113147

Remove in this Direction


While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

NOTICE:

The front pillar garnish clip is reusable if it is not damaged.



d.

When the front pillar garnish clip cannot be removed using your fingers:

i.
B431757C01
2.844,0.604 3.021,0.802 0.177,0.198 10 true 1
V113147

Lift in this Direction (1)


While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow (1) shown in the illustration.


ii.
B431759C01
2.854,0.99 3.042,1.208 0.188,0.219 10 true 2
V113147

Pull in this Direction (2)


While pulling the front pillar garnish clip in the direction indicated by the arrow (2), push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.

NOTICE:

If the front pillar garnish clip is damaged, replace it with a new one.




e.
B431754C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.


f.
B431761C01
0.854,1.844 0.854,1.375 true 1.604,2.188 1.604,1.719 true 1.792,2.479 2.146,2.479 true 2.719,2.302 3.052,2.302 true 2.552,1.74 2.552,1.271 true 2.219,1.26 2.031,1.052 true 3.135,0.76 3.021,0.51 true 2.875,0.979 3.031,0.979 true 0.792,1.844 1.104,2 0.313,0.156 10 false *1 2.729,0.885 3.042,1.042 0.313,0.156 10 false *a 1.635,2.385 1.948,2.542 0.313,0.156 10 false *b 2.49,1.74 2.688,1.927 0.198,0.188 10 true *1 1.542,2.188 1.854,2.344 0.313,0.156 10 false *a 3.073,2.219 3.281,2.375 0.208,0.156 10 true *b 1.885,0.958 2.094,1.115 0.208,0.156 10 false *b 3.167,0.688 3.375,0.844 0.208,0.156 10 false *b
*1 Curtain Shield Airbag Assembly LH
*a Protective Cover
*b Adhesive Tape


Protect the curtain shield airbag assembly LH.

i.

Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.




Hide 67918A 18.REMOVE REAR DOOR SCUFF PLATE LH

a.
B431763C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw as shown in the illustration.


b.
B431766C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.


Hide 62332A 19.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 73233 20.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 73220 21.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 22.REMOVE LOWER CENTER PILLAR GARNISH LH

a.
B431769C01
0.688,2.521 1.042,2.438 false 2.292,2.344 2.646,2.385 false 1.417,2.542 0.938,2.875 true 2.188,2.469 2.417,2.615 true 0.531,2.438 0.844,2.594 0.313,0.156 10 false *a 0.792,2.823 1.01,3.01 0.219,0.188 10 false *b 2.667,2.292 2.979,2.448 0.313,0.156 10 false *a 2.438,2.552 2.656,2.74 0.219,0.188 10 false *b
*a Claw (A)
*b Claw (B)
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the lower center pillar garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).


b.

Pull the lower center pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).


c.
B431771C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.


Hide 62420A 23.REMOVE CENTER PILLAR GARNISH ASSEMBLY LH

a.
B431775

Using a clip remover, remove the 2 clips.


b.
B431779C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


c.
B431777C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the clip and 2 guides to remove the center pillar garnish assembly LH as shown in the illustration.


Hide 67913 24.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111C 25.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 26.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 27.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 28.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62331A 29.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 30.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 73210 31.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 32.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62410A 33.REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 34.REMOVE REAR SEAT ASSEMBLY

Hide 76974F 35.REMOVE REAR UNDER SIDE COVER LH

a.
B437814C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 clips.


b.

Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.


Hide 71304C 36.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.
B431783

Loosen the bolt to remove the rear seatback hinge sub-assembly LH.


Hide 62552F 37.REMOVE REAR SEAT SIDE GARNISH LH

a.
B431785C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw as shown in the illustration.


b.
B431788C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 clips and 2 guides to remove the rear seat side garnish LH as shown in the illustration.


Hide 58460D 38.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

a.
B431791

Remove the bolt.


b.

Disengage the guide to remove the luggage hold belt striker assembly.


Hide 64937A 39.REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for LH Side)

a.
B431793C01
2.063,1.302 2.344,1.031 true 2.354,0.927 2.542,1.135 0.188,0.208 10 true *a
*a Protective Tape
V113146

Insert Screwdriver Here
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 1 tonneau cover holder cap as shown in the illustration.


Hide 64938 40.REMOVE TONNEAU COVER HOOK A (for LH Side)

a.
B431795C01
1.792,1.708 1.438,1.458 true 1.813,1.615 2.031,1.802 0.219,0.188 10 true *a
*a Protective Tape
V113146

Insert Screwdriver Here
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the tonneau cover hook A as shown in the illustration.


Hide 81330 41.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 64740C 42.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.
B439366C01
0.917,1.76 1.229,1.76 true 1.26,1.688 1.573,1.844 0.313,0.156 10 false *1
*1 No. 2 Luggage Compartment Trim Hook


Lower the No. 2 luggage compartment trim hook as shown in the illustration.


b.
B439367C02
2,1.031 2.302,1.031 true 1.708,1.167 1.708,1.49 true 0.771,2.771 0.771,3.094 true 1.479,2.844 1.479,3.052 true 2.323,0.927 2.635,1.083 0.313,0.156 10 false *1 0.708,3.094 1.021,3.25 0.313,0.156 10 false *a 1.656,1.521 1.969,1.677 0.313,0.156 10 false *b 1.417,3.063 1.729,3.219 0.313,0.156 10 false *c
*1 No. 2 Luggage Compartment Trim Hook
*a Protective Tape
*b Hole (A)
*c Clip
V113146

Insert Screwdriver Here
V113147

Push in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.

HINT:

Insert the screwdriver into the hole (A).



c.
B433770

Remove the 2 screws.


d.

Disengage the 5 claws, 2 clips and guide to remove the deck trim side panel assembly LH as shown in the illustration.

B433782C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 62480A 43.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

a.

Disengage the 5 clips as shown in the illustration to remove the roof side inner garnish assembly LH.

B433777C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 76973F 44.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71303C 45.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62551F 46.REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 58460D 47.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64937A 48.REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64938 49.REMOVE TONNEAU COVER HOOK A (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64730B 50.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62470A 51.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 52.REMOVE ROOF CONSOLE BOX ASSEMBLY

Hide 81240 53.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 89437D 54.REMOVE SENSOR COVER (w/ Humidity Sensor)

Hide 88620E 55.REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

Hide 89943 56.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 89941 57.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 87834 58.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Inner Rear View Mirror Stay Holder Cover)

Hide 86466E 59.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense)

Hide 86466D 60.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense)

Hide 61.REMOVE ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for all assist grip assemblies.


a.
B433785C01
1.625,2.542 1.625,2.177 true 1.563,2.552 1.771,2.729 0.208,0.177 10 true *a
*a Protective Tape
V113146

Insert Screwdriver Here


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the assist grip cover LH.

HINT:

Use the same procedure for the RH side and LH side.



b.
B433787C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.


c.

Remove the 2 clips from the vehicle body.


Hide 74630E 62.REMOVE REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip assembly.


Hide 74620C 63.REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip assembly.


Hide 74325 64.REMOVE VISOR BRACKET COVER (for LH Side)

a.
B433789C01
0,0 0,0 false
V113146

Insert Moulding Remover Here


Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover.


Hide 74320 65.REMOVE VISOR ASSEMBLY LH

a.
B433791

Remove the 2 screws.


b.
B433793C01
1.958,0.49 2.323,0.594 true 1.76,0.396 1.948,0.583 0.188,0.188 10 true *1
*1 Visor Holder
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder.


c.

Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.


Hide 74348C 66.REMOVE VISOR HOLDER LH

a.
B433794C02
1.563,0.125 1.781,0.333 0.219,0.208 10 true *a
*a 45°
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder approximately 45° and pull it out as indicated by the arrows, in the order shown in the illustration.


b.

Disengage the 2 claws to remove the visor holder.


Hide 74325 67.REMOVE VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74310 68.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348B 69.REMOVE VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 70.REMOVE ROOF HEADLINING ASSEMBLY

a.

for Windshield Glass Side:

i.

Disconnect each connector.



b.

for Front Pillar LH Side:

i.

Remove the protective cover.


ii.
B433809

Using a clip remover, disengage the 4 clamps.


iii.

Disconnect the 2 connectors.


iv.

Install the protective cover.



c.

for Front Pillar RH Side:

i.

Remove the protective cover.


ii.
B433805

Using a clip remover, disengage the 3 clamps.


iii.

Disconnect each connector.


iv.

Install the protective cover.



d.
B433811

for Rear Pillar RH Side:

i.

Disconnect the 2 connectors.



e.

for Roof Side (w/o Sliding Roof):

B433841C01
1.281,2.563 1.563,2.844 0.281,0.281 12 true *A
*A w/ Television Antenna - -


i.

w/ Television Antenna:

1.

Disconnect the connector.



ii.

Using a clip remover, remove the 3 clips.



f.

for Roof Side (w/ Sliding Roof):

B433842C01
3.042,2.198 3.042,1.823 true 2.875,1.521 2.521,1.229 2.521,1.229 3.094,1.458 true 3.76,2 4.281,2.24 4.281,2.24 3.948,1.958 true 4.052,1.719 4.219,1.427 4.219,1.427 3.729,1.51 true 1.302,3.542 1.302,3.292 true 2.365,1.146 2.677,1.302 0.313,0.156 10 false *a 2.958,2.208 3.198,2.385 0.24,0.177 10 true *b 4.292,2.167 4.51,2.354 0.219,0.188 10 true *a 4.25,1.313 4.469,1.5 0.219,0.188 10 true *a 1.229,3.531 1.469,3.708 0.24,0.177 10 true *c
*a Fastener *b Guide
*c Clamp - -


i.

Using a clip remover, disengage the clamp.


ii.

Disconnect each connector.


iii.

Using a clip remover, remove the 3 clips.


iv.

Disengage the 6 fasteners and guide.



g.
B433818C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.