Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR(for Center Pillar)
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230375 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the side airbag sensor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 4.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the lower center pillar garnish.


Hide 67917A 5.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the lower center pillar garnish.


Hide 62414A 7.REMOVE LOWER CENTER PILLAR GARNISH

Hide 89860A 8.REMOVE SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B432353

Remove the bolt and disengage the claw to separate the side airbag sensor assembly.


d.

Disconnect the connector to remove the side airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

C195226C18
3.927,1.313 3.927,2.146 false 1.385,1.313 1.385,2.146 true 1.135,0.99 1.135,0.531 1.135,0.531 1.052,0.531 true 3.646,1 3.646,0.542 3.646,0.542 3.563,0.542 true 0.948,1.156 0.417,0.729 true 3.469,1.146 2.938,0.74 true 0.854,0.438 1.042,0.615 0.188,0.177 10 false *a 3.375,0.469 3.563,0.646 0.188,0.177 10 false *a 1.313,2.208 1.5,2.385 0.188,0.177 10 false *b 0.969,1.708 1.156,1.885 0.188,0.177 10 false *c 3.531,1.729 3.719,1.906 0.188,0.177 10 false *c 3.823,2.177 4.01,2.354 0.188,0.177 10 false *b 1.427,0.625 1.615,0.802 0.188,0.177 10 false *d 3.875,0.646 4.063,0.823 0.188,0.177 10 false *d 0.281,0.615 0.448,0.823 0.167,0.208 10 false A 2.792,0.625 3.042,0.813 0.25,0.188 10 false A
*a White Housing Lock *b Yellow CPA
*c Slide *d Push



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




e.

After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect



Hide 89860C 9.REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY (w/ Airbag Cut Off Switch)

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the side No. 2 airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B312073C08
4.354,1 4.896,0.979 true 3.813,1.75 3.813,1.365 false 0.74,2.448 0.271,1.875 true 4.156,0.708 4.531,0.646 true 4.938,0.875 5.25,1.031 0.313,0.156 10 false *a 3.74,1.792 4.052,1.948 0.313,0.156 10 false *b 0.125,1.719 0.438,1.875 0.313,0.156 10 false *c 4.583,0.563 4.896,0.792 0.313,0.229 10 false A
*a White Housing Lock *b Yellow CPA
*c Connector lock is released - -



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




d.
B432354

Remove the bolt and disengage the claw to remove the side No. 2 airbag sensor assembly.


e.

Check that the position of the white housing lock is as shown in the illustration.

B296255C05
4.76,1.833 5.031,2.104 0.271,0.271 10 false *b 1.396,1.833 1.677,2.115 0.281,0.281 10 false *b 4.76,0.573 5.031,0.875 0.271,0.302 10 false *a 1.396,0.573 1.677,0.865 0.281,0.292 10 false *a
*a Incorrect *b Correct