1. PRECAUTION
Make sure to perform initialization after replacing the air conditioning radiator damper servo sub-assembly. If initialization is not performed, the air conditioner unit assembly will not perform properly as the air conditioning amplifier assembly will not be able to recognize the position of the air conditioning radiator damper sub-assembly.
87211A
2.REMOVE NO. 2 AIR DUCT (for LHD)
Remove the screw.
Disengage the 3 claws to remove the No. 2 air duct.
87211
3.REMOVE NO. 1 AIR DUCT (for RHD)
Remove the screw.
Disengage the 3 claws to remove the No. 1 air duct.
88897P
4.REMOVE ASPIRATOR
Disengage the 2 claws to remove the aspirator.
82143
5.REMOVE NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)
Disconnect the 2 connectors.
Disengage the 5 clamps to remove the No. 3 instrument panel wire.
87130D
6.REMOVE BLOWER ASSEMBLY
87114B
7.REMOVE HEATER COVER (w/o PTC Heater)
|
Remove in this Direction |
Remove the screw and heater cover as shown in the illustration.
87114L
8.REMOVE NO. 2 HEATER COVER (w/ PTC Heater)
Remove the screw.
Disengage the claw and guide to remove the No. 2 heater cover.
87710G
9.REMOVE QUICK HEATER ASSEMBLY (w/ PTC Heater)
|
Remove in this Direction |
Disengage the guide and remove the quick heater assembly as shown in the illustration.
88650N
10.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
for LHD:
|
Remove in this Direction |
Disconnect the connector.
Remove the screw.
Disengage the guide to remove the air conditioning amplifier assembly as shown in the illustration.
for RHD:
|
Remove in this Direction |
Disconnect the connector.
Remove the screw.
Disengage the guide to remove the air conditioning amplifier assembly as shown in the illustration.
82210K
11.REMOVE AIR CONDITIONING HARNESS ASSEMBLY
for LHD:
Disconnect each connector.
Disengage each clamp to remove the air conditioning harness assembly.
for RHD:
Disconnect each connector.
Disengage each clamp to remove the air conditioning harness assembly.
88539J
12.REMOVE DRAIN COOLER HOSE
Remove the drain cooler hose.
87050C
13.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Remove the 2 screws and No. 1 air conditioning radiator damper servo sub-assembly.
87050D
14.REMOVE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Remove the 3 screws and No. 2 air conditioning radiator damper servo sub-assembly.
87050E
15.REMOVE NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Remove the 2 screws and No. 3 air conditioning radiator damper servo sub-assembly.
87128
16.REMOVE HEATER GROMMET
Remove the heater grommet.
87124B
17.REMOVE HEATER CLAMP
Disengage the 4 claws to remove the heater clamp.
87107A
18.REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
|
Remove in this Direction |
Remove the heater radiator unit sub-assembly as shown in the illustration.
Prepare a drain pan or cloth in case the coolant leaks.
88515
19.REMOVE COOLER EXPANSION VALVE
Remove the cooling unit parts.
Using a 4 mm hexagon socket wrench, remove the 2 hexagon bolts and cooler expansion valve.
Remove the 2 O-rings from the No. 1 cooler evaporator sub-assembly.
88501
20.REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Remove the 2 screws.
Disengage the 10 claws to remove the upper heater case with No. 1 cooler evaporator sub-assembly from the lower heater case.
Disengage the clamp.
Remove the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor from the upper heater case.
88625
21.REMOVE NO. 1 COOLER THERMISTOR