88625
1.INSTALL NO. 1 COOLER THERMISTOR
88501
2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.
Engage the clamp.
Engage the 10 claws to install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case.
Install the 2 screws.
88515
3.INSTALL COOLER EXPANSION VALVE
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.
ND-OIL 11 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.
Install the cooling unit parts.
87107A
4.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
|
Install in this Direction |
Install the heater radiator unit sub-assembly as shown in the illustration.
87124B
5.INSTALL HEATER CLAMP
Engage the 4 claws to install the heater clamp.
87128
6.INSTALL HEATER GROMMET
Install the heater grommet.
87050E
7.INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
for LHD:
| *a | Reference Point |
Using the reference points, install the No. 3 air conditioning radiator damper servo sub-assembly with the 2 screws.
for RHD:
| *a | Reference Point |
Using the reference points, install the No. 3 air conditioning radiator damper servo sub-assembly with the 2 screws.
87050D
8.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
for Single Air Conditioning System:
Align each gear on the air conditioner radiator assembly as shown in the illustration, and then check that the gears of the No. 2 air conditioning radiator damper servo sub-assembly are aligned as shown in the illustration.
| *a | Reference Point | - | - |
Install the No. 2 air conditioning radiator damper servo sub-assembly with the 3 screws.
for Dual Air Conditioning System:
Align each gear on the air conditioner radiator assembly as shown in the illustration, and then check that the gears of the No. 2 air conditioning radiator damper servo sub-assembly are aligned as shown in the illustration.
| *a | Reference Point | - | - |
Using the reference points, install the No. 2 air conditioning radiator damper servo sub-assembly with the 3 screws.
| *a | Reference Point | - | - |
87050C
9.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
for LHD:
| *a | Link |
Connect the 3 links of the No. 1 air conditioning radiator damper servo sub-assembly to the 3 links of the air conditioning radiator assembly as shown in the illustration.
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.
for RHD:
| *a | Link |
Connect the 2 links of the No. 1 air conditioning radiator damper servo sub-assembly to the 2 links of the air conditioning radiator assembly as shown in the illustration.
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.
88539J
10.INSTALL DRAIN COOLER HOSE
| *a | Hose Notch |
| *b | Rib |
Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.
82210K
11.INSTALL AIR CONDITIONING HARNESS ASSEMBLY
for LHD:
Engage each clamp.
Connect each connector to install the air conditioning harness assembly.
for RHD:
Engage each clamp.
Connect each connector to install the air conditioning harness assembly.
88650N
12.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
for LHD:
|
Install in this Direction |
Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.
Install the air conditioning amplifier assembly with the screw.
Connect the connector.
for RHD:
|
Install in this Direction |
Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.
Install the air conditioning amplifier assembly with the screw.
Connect the connector.
87114B
13.INSTALL HEATER COVER (w/o PTC Heater)
|
Install in this Direction |
Install the heater cover with the screw as shown in the illustration.
87710G
14.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)
|
Install in this Direction |
Engage the guide to install the quick heater assembly as shown in the illustration.
87114L
15.INSTALL NO. 2 HEATER COVER (w/ PTC Heater)
Engage the guide and claw.
Install the No. 2 heater cover with the screw.
87130D
16.INSTALL BLOWER ASSEMBLY
82143
17.INSTALL NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)
Engage the 5 clamps to install the No. 3 instrument panel wire.
Connect the 2 connectors.
88897P
18.INSTALL ASPIRATOR
Engage the 2 claws to install the aspirator.
87211
19.INSTALL NO. 1 AIR DUCT (for RHD)
Engage the 3 claws.
Install a new No. 1 air duct with the screw.
87211A
20.INSTALL NO. 2 AIR DUCT (for LHD)
Engage the 3 claws.
Install a new No. 2 air duct with the screw.