Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0231469 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81056 1.REMOVE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY

Hide 81134 2.REMOVE HEADLIGHT GASKET

Hide 81144 3.REMOVE NO. 1 HEADLIGHT COVER

a.
E336995C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the No. 1 headlight cover as shown in the illustration to remove it.


Hide 81510C 4.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E336989C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove them as a unit.


b.

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 81515B 5.REMOVE FRONT TURN SIGNAL LIGHT SOCKET

Hide 81171B 6.REMOVE HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.



a.
E336997C01
0.448,0.302 0.76,0.5 0.313,0.198 10 false *a 1.646,0.135 1.958,0.333 0.313,0.198 10 false *a 1.938,0.563 2.25,0.76 0.313,0.198 10 false *a 2.302,1.604 2.615,1.802 0.313,0.198 10 false *a 1.594,1.979 1.906,2.177 0.313,0.198 10 false *a 0.469,1.844 0.781,2.042 0.313,0.198 10 false *a 3,1.438 3.313,1.635 0.313,0.198 10 false *b
*a Screw
*b "TORX" screw


Remove the 6 screws.


b.

Using a T20H "TORX" driver, remove the "TORX" screw.


c.
E336998

Using a dryer, heat the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



d.
E336999

Disengage the 8 claws.


e.

Separate the headlight lens.

HINT:

If the headlight lens cannot be separate even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens. Be careful not to damage the headlight lens and housing.



f.
E337000

Disconnect the connector to remove the headlight lens.


Hide 81132B 7.REMOVE HEADLIGHT LENS GASKET

a.
E337001

Remove the headlight lens gasket.

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



Hide 81171A 8.REMOVE HEADLIGHT UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.



a.
E337004

Disconnect the connector.


b.
E337006

Disengage the pivot collar.


c.
E337002C01
0,0 0,0 false
V113147

Turn in this Direction


While holding the headlight unit by hand, turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



d.
E337005

Disengage the 4 claws to remove the headlight unit.


Hide 85662 9.REMOVE HEADLIGHT LEVELING MOTOR

a.
E337007

Disconnect the connector.


b.

Remove the 2 screws and headlight leveling motor.