Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0231469 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 85662 1.INSTALL HEADLIGHT LEVELING MOTOR

a.
E337008

Install the headlight leveling motor with the 2 screws.


b.

Connect the connector.


Hide 81171A 2.INSTALL HEADLIGHT UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit or other components.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.



a.
E337006

Engage the pivot collar.


b.
E337005

Engage the 4 claws to temporarily install the headlight unit.


c.
E337003C01
0,0 0,0 false
V113147

Turn in this Direction


While holding the headlight unit by hand, turn the aiming screws as shown in the illustration to install the headlight unit.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



d.
E337004

Connect the connector.


Hide 81132B 3.INSTALL HEADLIGHT LENS GASKET

a.

Completely remove the old headlight lens gasket.


b.
E337001C01
0,0 0,0 false
V100155

Cleaning Area


Clean the installation groove of the headlight lens.


c.
E237693C09
1.323,1.281 1.365,1.042 false 0.625,1.125 0.667,0.896 false 1.229,1.292 1.531,1.542 0.302,0.25 10 false *a 0.531,1.146 0.865,1.396 0.333,0.25 10 false *b 1.479,1.875 2.01,2.177 0.531,0.302 10 false *c 1.521,0.542 1.677,0.74 0.156,0.198 10 false 1 0.302,0.635 0.458,0.833 0.156,0.198 10 false 2
*a Release Paper
*b Tape
*c 45°


Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.


d.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


e.

Using scissors, cut the end of the headlight lens gasket at a 45° angle.


f.
E342643C01
0,0 0,0 false
V100144

Starting Position


Starting from the position shown in the illustration and moving counterclockwise, temporarily install the headlight lens gasket as shown in the illustration.

NOTICE:

Gently install the headlight lens gasket without pulling it.



g.
E342644C01
0,0 0,0 false
V100135

Corner Groove


Set the headlight lens gasket into the corner groove.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner groove.




h.
E342645C01
0,0 0,0 false
V113147

Press in this Direction
V100155

Release Paper


Using 2 screwdrivers with their tips wrapped with release paper, completely press the headlight lens gasket into the groove to install it.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly in the corner groove.




i.
E342646C01
0.823,2.958 0.979,3.156 0.156,0.198 10 false A
A 10 mm (0.394 in.) or more
V100135

Corner Groove


Repeat the following until the headlight lens gasket reaches the starting position: Temporarily install the headlight lens gasket to the straight groove and completely press it into the groove, and then temporarily install it to the corner groove and completely press it into the groove.


j.

After installing the headlight lens gasket completely, check that the ends overlap for 10 mm (0.394 in.) or more.


k.

Check the installation condition of the headlight lens gasket.

NOTICE:
·

Make sure the headlight lens gasket is not protruding and is installed properly.

·

Make sure there is no gap between the ends of the headlight lens gasket.

·

Make sure to thoroughly check the corners as the headlight lens gasket is likely to be improperly installed in the corners.




Hide 81171B 4.INSTALL HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.



a.

Clean the sealing surface of the headlight lens.


b.
E337000

Connect the connector.


c.
E336999

Engage the 8 claws to install the headlight lens to the housing.

NOTICE:

Make sure all of the claws are engaged.



d.
E336997C01
0.448,0.302 0.76,0.5 0.313,0.198 10 false *a 1.646,0.135 1.958,0.333 0.313,0.198 10 false *a 1.938,0.563 2.25,0.76 0.313,0.198 10 false *a 2.302,1.604 2.615,1.802 0.313,0.198 10 false *a 1.594,1.979 1.906,2.177 0.313,0.198 10 false *a 0.469,1.844 0.781,2.042 0.313,0.198 10 false *a 3,1.438 3.313,1.635 0.313,0.198 10 false *b
*a Screw
*b "TORX" screws


Install the 6 screws.


e.

Using a T20H "TORX" driver, install the "TORX" screw.


f.

Check the installation condition of the headlight lens gasket.

NOTICE:

Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.



Hide 81515B 5.INSTALL FRONT TURN SIGNAL LIGHT SOCKET

Hide 81510C 6.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the front turn signal light socket.


b.
E336990C01
0,0 0,0 false
V113147

Install in this Direction


Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install them as a unit.


Hide 81144 7.INSTALL NO. 1 HEADLIGHT COVER

a.
E336996C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 headlight cover as shown in the illustration to install it.


Hide 81134 8.INSTALL HEADLIGHT GASKET

Hide 81056 9.INSTALL NO. 1 HEADLIGHT ECU SUB-ASSEMBLY