Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0232278 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  


DESCRIPTION

The forward recognition camera receives vehicle stability signals from the airbag ECU assembly. If the airbag ECU assembly detects an abnormal yaw rate sensor signal or yaw rate sensor power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit 2 seconds after the power switch is turned on (IG), a signal from the yaw rate sensor indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more.
·

Electronically controlled brake system

·

Yaw rate sensor (Airbag ECU assembly)

·

Forward recognition camera


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit 2 seconds after the power switch is turned on (IG), a signal from the yaw rate sensor indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more.
·

Electronically controlled brake system

·

Yaw rate sensor (Airbag ECU assembly)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

The road sign assist system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Road sign assist system DTC C1AA4 or C1AA5 may be stored due to a malfunction in the electronically controlled brake system. Therefore it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


a.

Check if DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)

B

2.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
4.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B