Home › Engine / Hybrid System › 2ZR-FXE COOLING › COOLANT(for Engine) › 2015.11–2016.08
RM3210E _51 Engine / Hybrid System _047499 2ZR-FXE COOLING _0233434 COOLANT(for Engine) A

2ZR-FXE COOLING  COOLANT(for Engine)  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
A389825

Do not remove the reserve tank cap, air release valve (w/ air release valve) or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 51444C 1.REMOVE REAR MOTOR UNDER COVER LH

Hide 2.DRAIN ENGINE COOLANT (for Engine)

CAUTION:

Do not remove the reserve tank cap, air release valve (w/ air release valve) or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.
A380106C02
1.531,2.042 1.958,2.042 false 1.927,3.948 2.365,3.948 false 1.74,3.229 2.177,3.229 false 2.417,3.885 2.729,4.042 0.313,0.156 10 false *1 2,1.958 2.24,2.125 0.24,0.167 10 true *a 2.219,3.156 2.458,3.323 0.24,0.167 10 true *a
*1 No. 1 Engine Under Cover
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.

Loosen the radiator drain cock plug.

A389826C01
1.688,0.219 2.156,0.219 false 5.25,0.24 5.719,0.24 false 2.365,2.302 2.74,2.302 false 5.906,2.292 6.281,2.292 false 4.458,0.323 4.927,0.323 false 0.385,0.063 0.719,0.365 0.333,0.302 12 false *A 3.792,0.083 4.115,0.385 0.323,0.302 12 false *B 2.208,0.135 2.521,0.292 0.313,0.156 10 false *1 2.781,2.208 3.094,2.365 0.313,0.156 10 false *2 5.76,0.146 6.073,0.302 0.313,0.156 10 false *1 6.323,2.208 6.635,2.365 0.313,0.156 10 false *2 4.302,0.24 4.615,0.396 0.313,0.156 10 false *a
*A w/o Air Release Valve *B w/ Air Release Valve
*1 Reserve Tank Cap *2 Radiator Drain Cock Plug
*a Air Release Valve - -



c.

Remove the reserve tank cap. Then drain the engine coolant.

HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD ENGINE COOLANT (for Engine)

a.
A378037C01
2.01,0.698 2.219,0.333 2.219,0.333 2.427,0.333 false 2.49,0.24 2.802,0.396 0.313,0.156 10 false *a
*a Identification Mark


Check the identification mark on the fan shroud assembly.


b.

w/ Air Release Valve:

i.
A390663C01
2.01,0.896 2.125,0.51 2.125,0.51 2.281,0.51 true 1.552,2.563 1.958,2.563 true 2.344,0.406 2.625,0.615 0.281,0.208 10 true *a 1.99,2.469 2.271,2.677 0.281,0.208 10 true *a
*a Air Release Valve


Using a 6 mm hexagon socket wrench, remove the air release valve from the radiator reserve tank assembly.



c.

Add coolant to the level shown in the illustration.

A389828C01
0.875,0.052 1.25,0.281 0.375,0.229 12 false *A 3.917,0.052 4.25,0.344 0.333,0.292 12 false *B
*A w/o Air Release Valve *B w/ Air Release Valve


Specified Capacity:
Identification Mark: R1 w/ Exhaust Heat Recirculation System 6.0 liters (6.3 US qts, 5.3 Imp. qts)
w/o Exhaust Heat Recirculation System 5.4 liters (5.7 US qts, 4.8 Imp. qts)
Identification Mark: R2 5.7 liters (6.0 US qts, 5.0 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



d.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

If the engine coolant level is low, add engine coolant.


e.

w/ Air Release Valve:

i.

Using a 6 mm hexagon socket wrench, install the air release valve to the radiator reserve tank assembly.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)



f.

Install the reserve tank cap.

NOTICE:

Securely tighten the reserve tank cap as much as possible.



g.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


h.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off.

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.

Warm up the engine until the water inlet with thermostat sub-assembly opens. While the water inlet with thermostat sub-assembly is open, circulate the engine coolant for several minutes.

HINT:

The water inlet with thermostat sub-assembly open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.



ii.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.

CAUTION:
When squeezing the No. 1 radiator hose and No. 2 radiator hose:
·

Wear protective gloves.

·

Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.

·

Keep your hands away from the fan LH and fan RH.



NOTICE:
·

Make sure that the radiator reserve tank assembly still has some engine coolant in it.

·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.

·

If the radiator reserve tank assembly does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the radiator reserve tank assembly is filled to the FULL line.





i.

After the engine has cooled down, check that the engine coolant level is between the FULL line and LOW line.

If the engine coolant level is below the LOW line, add engine coolant to the FULL line.


Hide 4.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51444C 5.INSTALL REAR MOTOR UNDER COVER LH