Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM3210E _59 Vehicle Exterior _047514 WIPER / WASHER _0233572 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E337244C01
1.5,1.427 1.51,1.302 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push the windshield wiper motor assembly in the direction indicated by the arrow (1), then move the windshield wiper motor assembly in the direction indicated by the arrow (2) shown in the illustration to temporarily install it to the windshield wiper link assembly.


b.

Install the windshield wiper motor assembly with the 3 bolts.

Torque:
5.39 N*m (55 kgf*cm, 48 in.*lbf)


c.
E337247

Apply MP grease to the pivot of the windshield wiper motor assembly.


d.
E337238C01
2.104,0.854 2.552,0.688 false 2.573,0.552 2.885,0.75 0.313,0.198 10 false *a
*a Pivot of Windshield Wiper Motor Assembly


Connect the No. 1 windshield wiper link rod to the pivot of the windshield wiper motor assembly.


Hide 85110 2.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.

Install the windshield wiper motor assembly to the windshield wiper link assembly with the 3 bolts.

Torque:
5.39 N*m (55 kgf*cm, 48 in.*lbf)


Hide 85012A 3.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY (for RHD)

a.

Connect the windshield wiper motor assembly connector.


b.

Turn the power switch on (IG).


c.

Operate the windshield wiper motor assembly and stop it at the automatic stop position.


d.

Turn the power switch off.


e.

Disconnect the windshield wiper motor assembly connector.


f.

Temporarily install the front wiper crank sub-assembly to the windshield wiper motor assembly with the nut.


g.

Set the No. 1 windshield wiper link rod on the pivot of the front wiper crank sub-assembly.


h.

Align the pivot of the front wiper crank sub-assembly with the shaft of the windshield wiper motor assembly and No. 1 windshield wiper link rod as shown in the illustration.

E331321C02
4.427,2.344 4.323,1.844 false 3.208,2.385 3.042,1.854 true 2.208,2.417 2.5,1.917 true 4.385,2.354 4.698,2.51 0.313,0.156 10 false *a 3.167,2.396 3.479,2.552 0.313,0.156 10 false *b 2.104,2.427 2.417,2.583 0.313,0.156 10 false *c
*a No. 1 Windshield Wiper Link Rod *b Shaft of Windshield Wiper Motor Assembly
*c Pivot of Front Wiper Crank Sub-assembly - -



i.
E331319C02
1.25,0.865 1.615,0.948 true 1.063,0.74 1.375,0.938 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, hold the front wiper crank sub-assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



j.

Tighten the nut.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


k.
E331322

Apply MP grease to the pivot of the front wiper crank sub-assembly.


l.
E331318C02
0.406,1.427 1.125,1.302 false 0.219,1.354 0.531,1.552 0.313,0.198 10 false *a
*a Pivot of Front Wiper Crank Sub-assembly


Connect the No. 1 windshield wiper link rod to the pivot of the front wiper crank sub-assembly.


Hide 4.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)

a.

Connect the connector.


b.
E337234C01
1.208,0.927 0.906,0.74 true 1.229,0.844 1.417,1.031 0.188,0.188 10 true *a
*a Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



c.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 5.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

a.

Connect the connector.


b.
E331315C02
0.469,1.083 0.885,0.906 true 0.271,0.99 0.448,1.167 0.177,0.177 10 true *a
*a Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



c.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 55781E 6.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 3 guides as shown in the illustration.

E337226C01
2.896,2.125 3.073,1.969 false
V113147

Install in this Direction - -


NOTICE:

When installing the cowl top ventilator louver sub-assembly, it may contact the brake master cylinder reservoir filler cap assembly and cause it to fall off. Check the installation condition of the brake master cylinder reservoir filler cap assembly after installing the cowl top ventilator louver sub-assembly.



b.

Engage the guide to install the cowl top ventilator louver sub-assembly as shown in the illustration.

E337222


c.

Install the 2 clips.


Hide 55754F 7.INSTALL COWL WATER EXTRACT SHIELD LH

a.
E337218C01
1.969,0.875 2.042,0.865 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws to install the cowl water extract shield LH as shown in the illustration.


Hide 55753D 8.INSTALL COWL WATER EXTRACT SHIELD RH

HINT:

Use the same procedure as for the LH side.


Hide 9.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

When reusing the front wiper arm and blade assembly RH:

i.
E337249C01
0.802,1.021 1.448,1.229 true 2.177,3.531 2.729,3.469 true 0.615,0.896 0.927,1.094 0.313,0.198 10 false *a 2.75,3.354 3.063,3.552 0.313,0.198 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Turn the power switch on (IG).


d.

Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.


e.

Turn the power switch off.


f.
E337250C01
0.781,1.052 0.74,0.74 false 0.729,1.063 0.917,1.25 0.188,0.188 10 true *a 0.344,0.385 0.5,0.583 0.156,0.198 10 false A 0.26,0.615 0.417,0.813 0.156,0.198 10 false A
*a Alignment Mark


Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 7.5 mm (0.295 in.)



Hide 10.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

When reusing the front wiper arm and blade assembly LH:

i.
E337252C01
0.833,1.125 1.448,1.313 true 2.188,3.521 2.729,3.438 true 0.646,1 0.958,1.198 0.313,0.198 10 false *a 2.75,3.323 3.063,3.521 0.313,0.198 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E337253C01
1.479,3.156 1.396,2.885 false 1.438,3.167 1.635,3.354 0.198,0.188 10 true *a 0.865,2.688 1.021,2.885 0.156,0.198 10 true A 0.875,2.927 1.031,3.125 0.156,0.198 10 true A
*a Alignment Mark


Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 7.5 mm (0.295 in.)



d.

Turn the power switch on (IG).


e.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.


f.

Turn the power switch off.


g.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


Hide 85292B 11.INSTALL FRONT WIPER ARM HEAD CAP

a.
E337212

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.



Hide 75534 12.INSTALL WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 13.INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.