Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WINDSHIELD OUTSIDE MOULDING
RM3210E _59 Vehicle Exterior _047542 EXTERIOR PANELS / TRIM _0243319 WINDSHIELD OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  WINDSHIELD OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75547C 1.INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.


a.
B436056

Using a riveter with a nose piece, install 5 new No. 3 windshield outside moulding clips.

HINT:

If the mandrel of the No. 3 windshield outside moulding clip does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
B398365C01
1.75,0.75 1.5,0.25 1.5,0.25 1.333,0.25 false 1.833,1.833 2.021,1.333 false 1.156,0.156 1.469,0.313 0.313,0.156 10 false *a 1.76,1.844 2.073,2 0.313,0.156 10 false *b 2.167,0.167 2.479,0.323 0.313,0.156 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


·

Do not pry the No. 3 windshield outside moulding clip with the riveter, as this will cause damage to the riveter and mandrel.


·
B398364C01
1.031,0.333 1.281,0.333 false 1.083,1.396 1.333,1.396 false 1.313,0.26 1.625,0.417 0.313,0.156 10 false *a 1.938,0.094 2.25,0.25 0.313,0.156 10 false *b 1.375,1.313 1.688,1.469 0.313,0.156 10 false *a 1.938,1.167 2.25,1.323 0.313,0.156 10 false *b
*a Riveter
*b Incorrect


Confirm that the No. 3 windshield outside moulding clips are seated properly against the vehicle body.


·

Do not tilt the riveter when installing the No. 3 windshield outside moulding clip to the vehicle body.




b.

Install the windshield glass sub-assembly.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>INSTALLATION


Hide 75545B 2.INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.


a.

Engage the 5 claws as shown in the illustration to install 5 new No. 1 windshield outside moulding clips.

B436054C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 75546B 3.INSTALL NO. 2 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a No. 2 windshield outside moulding clip is necessary.


a.
B436052C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clip as shown in the illustration to install a new No. 2 windshield outside moulding clip.


Hide 75534 4.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Engage the guide.


b.
B436050

Engage the 12 claws to install the windshield outside moulding.