Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P001013  A Camshaft Position Actuator Bank 1 Circuit Open  


DESCRIPTION

The Variable Valve Timing (VVT) system consists of the ECM, camshaft timing oil control valve assembly and camshaft timing gear assembly.

The VVT system controls the camshaft timing oil control valve assembly to operate the camshaft timing gear assembly and optimize the intake valve timing according to driving conditions. This control is performed based on the air flow volume, throttle position, engine coolant temperature, etc. Based on signals from each sensor, the ECM controls the position of the camshaft timing control valve assembly to change the relative position of the camshaft, enhance the engine torque and fuel economy and decrease the exhaust gas emissions. Using signals from the camshaft position sensor, the ECM detects the actual valve timing and performs feedback control to optimize the valve timing.

A209140E85
2.563,4.573 2.844,4.271 2.844,4.271 3.615,4.271 false 3.177,4.813 3.323,5.042 3.323,5.042 3.854,5.042 false 4.781,0.854 6.479,1.219 1.698,0.365 10 false Camshaft Position Sensor 4.771,1.344 6.5,1.5 1.729,0.156 10 false Crankshaft Position Sensor 0.073,0.031 0.948,0.229 0.875,0.198 10 false VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 false Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 false Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 false Correction 2.823,3.552 3.417,3.729 0.594,0.177 10 false ECM 1.604,3.792 4.531,3.979 2.927,0.188 10 false Camshaft Timing Oil Control Valve Assembly 0.167,2.688 0.865,2.865 0.698,0.177 10 false Duty-cycle 4.531,1.854 6.74,2.073 2.208,0.219 10 false Mass Air Flow Meter Sub-assembly 4.479,2.875 6.781,3.073 2.302,0.198 10 false Engine Coolant Temperature Sensor 4.865,2.365 6.396,2.531 1.531,0.167 10 false Throttle Position Sensor 4.917,3.385 6.354,3.563 1.438,0.177 10 false Vehicle Speed Signal 0.313,4.271 1.677,4.479 1.365,0.208 10 false Engine Oil Pressure 3.667,4.219 7.063,4.406 3.396,0.188 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.885,4.958 4.99,5.146 1.104,0.188 10 false Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001013 A Camshaft Position Actuator Bank 1 Circuit Open Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly circuit

·

Camshaft timing oil control valve assembly

·

ECM


Comes on DTC stored SAE Code: P0010

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve assembly duty-cycle is excessively high or low while the power switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P001013.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A330728E65
0.063,1.979 3.031,2.396 2.969,0.417 10 false Camshaft Timing Oil Control Valve Assembly 1.781,1.365 2.188,1.552 0.406,0.188 10 false 2 1.771,0.76 2.229,0.948 0.458,0.188 10 false 1 4.635,0.75 5.042,0.938 0.406,0.188 10 false 35 4.646,1.385 5.052,1.573 0.406,0.188 10 false 34 4.906,0.75 5.313,0.938 0.406,0.188 10 false OC1+ 4.917,1.385 5.323,1.573 0.406,0.188 10 false OC1- 5.021,2.229 5.427,2.417 0.406,0.188 10 false C31 5.385,2.229 6.021,2.49 0.635,0.26 10 false ECM 0.063,1.823 0.469,2.01 0.406,0.188 10 false C25 1.563,0.76 2.021,0.948 0.458,0.188 10 false + 1.563,1.365 1.969,1.552 0.406,0.188 10 false -

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P001013)
2.READ OUTPUT DTC (DTC P001013)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001013 is output B




A

B

3.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C25-1 (+) - C31-35 (OC1+) Always Below 1 Ω
C25-2 (-) - C31-34 (OC1-) Always Below 1 Ω
C25-1 (+) or C31-35 (OC1+) - Body ground and other terminals Always 10 kΩ or higher
C25-2 (-) or C31-34 (OC1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR