Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › ECM
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0244552 ECM A

2ZR-FXE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration (w/ Canister Pump Module) MIL comes on (Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module
Perform Vehicle Identification Number (VIN) or frame number registration (w/o Canister Pump Module)

*1: When performing learning using the GTS. Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>REGISTRATION



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89661 3.REMOVE ECM

a.
A375009C01
0.708,0.833 0.865,1.167 0.865,1.167 1.042,1.167 true 2.417,0.885 2.594,1.219 2.594,1.219 2.771,1.219 true 0.344,1.094 0.521,1.26 0.177,0.167 10 true *a 1.979,1.083 2.156,1.25 0.177,0.167 10 true *a 1.031,1.083 1.208,1.25 0.177,0.167 10 true *b 2.76,1.125 2.938,1.292 0.177,0.167 10 true *b
*a Push
*b Lock


Raise the 2 levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.
A375011

Disengage the 2 clamps.


c.

Remove the bolt and separate the engine wire from the No. 1 ECM bracket.


d.
A375012C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 4.REMOVE NO. 1 ECM BRACKET

a.
A375013

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 5.REMOVE NO. 2 ECM BRACKET

a.
A375014

Remove the 2 screws and No. 2 ECM bracket from the ECM.