Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P010515  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P010511.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P010511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010515 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open The manifold absolute pressure sensor output voltage is higher than 4.5 V for 0.5 seconds or more (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored SAE Code: P0108

HINT:

When this DTC is output, check the intake manifold absolute pressure in the Data List. Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.

DTC No. Intake Manifold Absolute Pressure Malfunction
P010515 Higher than 130 kPa (18.85 psi)
·

Short in VCPM to PIM circuit

·

Open in PIM circuit

·

Open in EPIM circuit



If the Data List value is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the manifold absolute pressure sensor voltage and uses this value to calculate the intake manifold pressure. When the manifold absolute pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold absolute pressure sensor circuit, illuminates the MIL and stores a DTC.

Example:

If the manifold absolute pressure sensor output voltage is higher than 4.5 V for 0.5 seconds or more, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and wait 5 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P010515.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A376493C01
0.417,1.042 0.76,1.292 0.344,0.25 0.927,1.729 1.396,1.26 true 1.458,1.885 1.708,1.292 true 2.479,1.854 2,1.281 true 0.51,1.094 0.823,1.292 0.313,0.198 10 false C3 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.802,1.76 1.115,1.958 0.313,0.198 10 false E2 1.313,1.927 1.771,2.125 0.458,0.198 10 false PIM 2.438,1.896 2.75,2.094 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C3-3 (VC) - C3-1 (E2) Power switch on (IG) 4.75 to 5.25 V
C3-2 (PIM) - C3-1 (E2) Power switch on (IG) 3.0 to 5.25 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-1 (E2) - Body ground Power switch off Below 1 Ω
C3-3 (VC) - C3-2 (PIM) Power switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-1 (E2) - C31-76 (EPIM) Always Below 1 Ω
C3-2 (PIM) - C31-78 (PIM) Always Below 1 Ω
C3-2 (PIM) or C31-78 (PIM) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR