Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P062F44  Internal Control Module EEPROM Data Memory Failure  


DESCRIPTION

The ECM monitors its internal operation and stores this DTC when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062F44 Internal Control Module EEPROM Data Memory Failure An ECM internal error (EEPROM) (1 trip detection logic). ECM Comes on DTC stored SAE Code: P062F

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the GTS off.

6.

Turn the power switch off.

7.

Disconnect the GTS.

8.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

9.

Connect the cable to the negative (-) auxiliary battery terminal.

10.

Connect the GTS to the DLC3.

11.

Turn the power switch on (IG).

12.

Turn the GTS on.

13.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

14.

Start the engine and wait 30 seconds or more.

15.

Enter the following menus: Powertrain / Engine / Trouble Codes.

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P062F44.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

NOTICE:
·

There is a possibility that the DTC P062F44 is issued from the ECUs of the ECM and hybrid vehicle control ECU.

Use GTS to conduct a health check to confirm which ECU the DTC is issued from and then inspect the related system.

·

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P062F44)
2.READ OUTPUT DTC (DTC P062F44)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

g.

Start the engine and wait 30 seconds or more.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P062F44 is output B




A

B