Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P10AA00  Clogged EGR Port Imbalance Bank1  P219A00  Bank 1 Air-Fuel Ratio Imbalance  P219C00  Cylinder 1 Air-Fuel Ratio Imbalance  P219D00  Cylinder 2 Air-Fuel Ratio Imbalance  P219E00  Cylinder 3 Air-Fuel Ratio Imbalance  P219F00  Cylinder 4 Air-Fuel Ratio Imbalance  


DESCRIPTION

Refer to DTC P030000.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P030000

Refer to DTC P04019C.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P04019C

Refer to DTC P21951D.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P21951D

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P10AA00 Clogged EGR Port Imbalance Bank1 The difference in the air fuel ratios between the cylinders exceeds the threshold when the EGR valve is open (2 trip detection logic). Intake manifold Comes on DTC stored SAE Code: P10AA
P219A00 Bank 1 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219A
P219C00 Cylinder 1 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219C
P219D00 Cylinder 2 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219D
P219E00 Cylinder 3 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219E
P219F00 Cylinder 4 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219F

MONITOR DESCRIPTION

Fuel System Air Fuel Ratio Cylinder Imbalance Monitor

The ECM uses the air fuel ratio sensor, crankshaft position sensor and EGR valve assembly to monitor the difference in air fuel ratios between the cylinders caused by differences in fuel injection volume between the cylinders, leakage in the intake or exhaust system, etc.

When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that there is a malfunction, illuminates the MIL and stores a DTC.


EGR Port Clogged Monitoring Method: P10AA00 is stored primarily when a rich side imbalance for clogged EGR port is detected.

By comparing the air fuel ratio when EGR valve is open and closed, a clog in an EGR port can be detected. If an EGR port is clogged when the EGR valve is open, the ECM will store a DTC.


Air Fuel Ratio Sensor Monitoring Method: P219A00 is stored primarily when a rich side imbalance is detected.

When the system detects a difference in air fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the ECM determines that there is a malfunction.


Crankshaft Position Sensor Monitoring Method: P219C00, P219D00, P219E00 and/or P219F00 are stored primarily when a lean side imbalance is detected.

The system monitors the engine speed variation and when the variation becomes large, the ECM determines that there is a difference in air fuel ratios between the cylinders, which it determines to be a malfunction.


MONITOR STRATEGY

Required Sensors/Components (Main) EGR valve assembly
Air fuel ratio sensor
Crankshaft position sensor
Required Sensors/Components (Related) Mass air flow meter sub-assembly
Engine coolant temperature sensor
Frequency of Operation Continuous: P10AA
Once per driving cycle: Others

TYPICAL ENABLING CONDITIONS

P10AA00: EGR Port Clogged Monitoring Method
Air fuel ratio sensor status Activated
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Fuel cut Off
EGR valve assembly malfunction Not detected
Both of the following conditions are met 1 and 2
1. EGR on delta air fuel ratio parameter is calculated when all of the following conditions are met -
Engine speed 1800 rpm or higher, and less than 2600 rpm
Fuel system status Closed loop
Engine load 40% or higher, and less than 60%
EGR valve operation More than 20 steps
2. EGR off delta air fuel ratio parameter is calculated when all of the following conditions are met -
Engine speed 1200 rpm or higher, and less than 2600 rpm
Engine load 40% or higher, and less than 70%
EGR valve operation 0 steps or less

P219A00: Air Fuel Ratio Sensor Monitoring Method
Air fuel ratio sensor status Activated
Engine speed 1600 rpm or more, and less than 2400 rpm
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Fuel system status Closed loop
Engine load 40% or more, and less than 60%

P219C00, P219D00, P219E00 and P219F00: Crankshaft Position Sensor Monitoring Method (First Judgment)
Engine speed 1200 rpm or more, and less than 1600 rpm
Engine Load 40% or more, and less than 60%
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher

P219C00, P219D00, P219E00 and P219F00: Crankshaft Position Sensor Monitoring Method (Second Judgment)
Vehicle speed Less than 3 km/h (2 mph)
Engine speed 1050 rpm or more, and less than 1350 rpm
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher

TYPICAL MALFUNCTION THRESHOLDS

P10AA00: EGR Port Clogged Monitoring Method
EGR port clogged monitoring method criteria 1 or more

P219A00: Air Fuel Ratio Sensor Monitoring Method
Air fuel ratio sensor monitoring method criteria 1 or more

Crankshaft Position Sensor Monitoring Method (First Judgment)
Crankshaft position sensor monitoring method criteria (first judgment) 1.5 or more

Crankshaft Position Sensor Monitoring Method (Second Judgment)
Crankshaft position sensor monitoring method criteria (second judgment) 1 or more

HINT:

If the first judgment while driving shows that the value of Engine Speed Fluctuation Average is between 0.5 and 1.5, then second judgment will be performed when the vehicle is stopped and the engine is idling.


CONFIRMATION DRIVING PATTERN

P10AA00
A377955E01
0.063,2.24 1.115,2.625 1.052,0.385 10 false Power Switch on (IG) 0.75,1.958 1.125,2.219 0.375,0.26 10 false Idling 0.073,1.479 1.115,1.917 1.042,0.438 10 false 10 km/h [Engine stopped] 0.094,0.646 1.104,1.219 1.01,0.573 10 false 50 to 60 km/h [Engine running] 1.438,2.677 2.01,3.115 0.573,0.438 10 false Warming up 2.542,2.604 3.094,3.073 0.552,0.469 10 false 10 to 15 seconds 4.427,2.615 4.979,3.083 0.552,0.469 10 false 10 to 15 seconds 3.833,3.229 4.917,3.552 1.083,0.323 10 false 15 to 20 times 1.604,1.823 2.688,2.146 1.083,0.323 10 false [B] 2.646,0.979 3.729,1.302 1.083,0.323 10 false [D] 3.708,0.979 4.792,1.302 1.083,0.323 10 false [E] 1.177,2.104 2.26,2.427 1.083,0.323 10 false [A] 4.167,2.969 5.25,3.292 1.083,0.323 10 false [F] 6.656,2.75 6.948,3.063 0.292,0.313 10 false [G] 2.063,2.51 3.146,2.833 1.083,0.323 10 false [C] 6.802,2.531 7.156,2.771 0.354,0.24 10 false Time 0.229,0.115 1.24,0.417 1.01,0.302 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

10.

Turn the power switch off. [C]

11.

Turn the power switch on (READY).

12.

Start the engine by depressing the accelerator pedal approximately 40% and accelerating the vehicle from 10 km/h (6 mph) to a speed between 50 and 60 km/h (31 to 37 mph) in 10 to 15 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine does not start, further depress the accelerator pedal.


13.

Decelerate the vehicle to less than 10 km/h (6 mph) and allow the engine to stop [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

The vehicle can be decelerated by any method.


14.

Repeat steps [D] and [E] above 15 to 20 times [F].

15.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P10AA00.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform the confirmation driving pattern and check the judgment result again.

·

If the judgment result is N/A, perform the following procedure.





P219A00, P219C00, P219D00, P219E00 and P219F00
A288663E08
4.729,3.51 4.427,3.51 false 4.427,3.5 4.083,2.625 false 5.167,3.156 4.573,3.156 false 5,3.156 4.896,2.635 false 4.573,3.146 4.406,2.625 false 1.875,2.625 1.979,3.125 false 1.979,3.115 2.563,3.115 false 2.448,3.115 2.375,2.615 false 1.563,2.646 1.729,3.49 false 1.729,3.479 1.885,3.479 false 1.813,0.781 2.219,1.104 0.406,0.323 10 false [C] 0.104,2.563 1.208,2.792 1.104,0.229 10 false Power Switch off 0.573,2.219 1.063,2.573 0.49,0.354 10 false Idling 0.052,1.604 0.948,2.042 0.896,0.438 10 false 40 km [Engine running] 0.031,0.969 0.948,1.635 0.917,0.667 10 false 80 km [Engine running] 0.01,0.417 1.01,0.813 1,0.396 10 false 100 km [Engine running] 1.073,2.042 1.563,2.313 0.49,0.271 10 false [A] 1.354,1.135 1.708,1.385 0.354,0.25 10 false [B] 2.313,2.031 2.833,2.333 0.521,0.302 10 false [D] 3.063,0.792 3.49,1.083 0.427,0.292 10 false [E] 3.854,0.75 4.271,1.094 0.417,0.344 10 false [G] 4.323,0.531 4.823,0.979 0.5,0.448 10 false [H] 3.76,3.167 4.052,3.417 0.292,0.25 10 false [F] 4.844,2.042 5.219,2.323 0.375,0.281 10 false [I] 5.573,0.531 6.063,0.906 0.49,0.375 10 false [J] 6.542,3.167 6.906,3.417 0.365,0.25 10 false [K] 0.042,0.031 1.427,0.25 1.385,0.219 10 false Vehicle Speed 6.781,2.583 7.135,2.906 0.354,0.323 10 false Time 1.917,3.396 3.156,3.719 1.24,0.323 10 false 10 to 20 seconds 2.573,3.021 3.844,3.344 1.271,0.323 10 false 1 minute or more 4.76,3.438 5.844,3.76 1.083,0.323 10 false 5 to 15 seconds 5.219,3.083 6.302,3.385 1.083,0.302 10 false 1 minute or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

5.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

6.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

NOTICE:

Use the GTS to clear the DTCs. (Do not disconnect the cable from negative (-) auxiliary battery terminal to clear the DTCs.)


7.

With the engine running, drive the vehicle at 40 km/h (25 mph) or higher.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


8.

With the engine running, gradually accelerate the vehicle from 40 km/h (25 mph) to 80 km/h (50 mph) taking approximately 10 to 20 seconds [B].

HINT:
·

Refer to engine load and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 80 km/h (50 mph).

·

If the engine stops, further depress the accelerator pedal to restart the engine.



9.

With the engine running, drive the vehicle at 80 km/h (50 mph) or higher for 1 minute or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Electrical load can be applied while the vehicle is driven.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



10.

Idle the engine for 1 minute or more [D].

HINT:

Perform this step with drive (D) selected.


11.

Repeat steps [B] and [D] above at least 3 times [E].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

With the engine running, drive the vehicle at 80 km/h (50 mph).

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


15.

With the engine running, gradually accelerate the vehicle from 80 km/h (50 mph) to 100 km/h (62 mph) taking approximately 5 to 15 seconds [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Refer to engine load and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 100 km/h (62 mph).

·

If the engine stops, further depress the accelerator pedal to restart the engine.



16.

With the engine running, drive the vehicle at 100 km/h (62 mph) or higher for 1 minute or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Electrical load can be applied while the vehicle is driven.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



17.

Idle the engine for 1 minute or more [I].

HINT:

Perform this step with drive (D) selected.


18.

Repeat steps [G] and [I] above at least 2 times [J].

19.

Enter the following menus: Powertrain / Engine / Trouble Codes [K].

20.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



21.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

22.

Input the DTC: P219A00, P219C00, P219D00, P219E00 or P219F00.

23.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform the confirmation driving pattern and check the judgment result again.

·

If the judgment result is N/A, perform the following procedure.





CAUTION / NOTICE / HINT

HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

When any air fuel ratio imbalance is detected, the ECM will perform air fuel ratio feedback control to make the air fuel ratio close to the stoichiometric air fuel ratio. This may result in an air fuel ratio imbalance of normal cylinders and DTCs may be stored.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 is output A
DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 and other DTCs are output B


HINT:

If any DTCs other than DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (FREEZE FRAME DATA)

B

2.READ VALUE USING GTS (FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>FREEZE FRAME DATA

Freeze Frame Data Items for DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00:
·

Vehicle Speed

·

Engine Speed

·

Calculate Load

·

Short FT Bank 1

·

Long FT Bank 1

·

Misfire Count Cylinder #1 to #4


HINT:

When the sum of Short FT Bank 1 and Long FT Bank 1 is positive, the engine is running lean, and when the sum is negative, the engine is running rich.

Air Fuel Ratio Sensor Monitoring Method (P219A00) Crankshaft Position Sensor Monitoring Method (P219C00, P219D00, P219E00 and P219F00) EGR Port Clogged Monitoring Method (P10AA00) Note
- - DTC is output Detected by EGR Port Clogged Monitoring Method.*1
DTC is output DTC is output (Only one DTC relating to a single cylinder is output) DTC is not output Malfunctioning of cylinders detected by Crankshaft Position Sensor Monitoring Method is primarily suspected
DTC is output DTCs are output (Multiple DTCs relating to multiple cylinders are output) DTC is not output Malfunctioning of cylinders except ones detected by Crankshaft Position Sensor Monitoring Method is primarily suspected.*2
DTC is not output DTCs are output DTC is not output Malfunctioning of cylinders detected by Crankshaft Position Sensor Monitoring Method is primarily suspected.
DTC is output DTCs are not output DTC is not output Malfunctioning of the bank detected by Air Fuel Ratio Sensor Monitoring Method is primarily suspected.

*1: Even if other DTCs are output, it is likely that an EGR port is clogged.

*2: When any air fuel ratio imbalance is detected, the ECM will perform air fuel ratio feedback control to make the air fuel ratio close to the stoichiometric air fuel ratio. This may result in an air fuel ratio imbalance of normal cylinders and DTCs may be stored.



Result:
Proceed to
NEXT



NEXT

3.READ OUTPUT DTC
3.READ OUTPUT DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Drive the vehicle in accordance with Confirmation Driving Pattern.

HINT:
·

If any misfire count (Misfire Count Cylinder #1 to #4) increases while idling or driving the vehicle, proceed to step 7.

·

Perform inspections while focusing on the cylinder whose misfire count has increased.

·

Perform the confirmation driving patterns for both DTC P10AA00 and P219A00.




f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P10AA00 is output A
DTC P219A00 is output B
DTC P219A00 and P219C00, P219D00 or P219E00 are output C
DTC P219C00, P219D00, P219E00 and/or P219F00 is output




A

4.REPLACE INTAKE MANIFOLD

B

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

C

7.CHECK INTAKE SYSTEM
4.REPLACE INTAKE MANIFOLD
a.

Replace the intake manifold.

HINT:

Perform "Inspection After Repair" after replacing the intake system.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up.

HINT:

The A/C switch and all accessories should be off and park (P) or neutral (N) should be selected.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / Misfire Count Cylinder #1 to #4.

HINT:

When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 7 (Check Intake System).


Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume
Data List Display
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
50004 372 7 148,149,150,151

g.

According to the display on the GTS, perform the Active Test with the engine idling.


h.

Check the misfire counts (Misfire Count Cylinder #1 to #4) while decreasing the injection volume in 5% increments.

Result:

The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR EXHAUST GAS LEAK
6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2ZR-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.INSPECT SPARK PLUG

NG

REPAIR OR REPLACE INTAKE SYSTEM

8.INSPECT SPARK PLUG
a.

Inspect the spark plug of the cylinder causing the imbalance.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

9.CHECK FOR SPARK (SPARK TEST)

NG

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

10.CHECK CYLINDER COMPRESSION PRESSURE
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
A201049C90
0.385,1.167 0.771,1.396 0.385,0.229 0.385,0.854 0.771,1.083 0.385,0.229 0.385,0.552 0.771,0.781 0.385,0.229 0.385,1.479 0.771,1.708 0.385,0.229 0.125,0.063 0.292,0.219 0.167,0.156 10 false *a 0.458,0.604 0.771,0.823 0.313,0.219 10 false C14 0.469,0.906 0.813,1.094 0.344,0.188 10 false C15 0.458,1.208 0.844,1.427 0.385,0.219 10 false C16 0.469,1.521 0.885,1.74 0.417,0.219 10 false C17
*a Front view of wire harness connector
(to Fuel Injector Assembly)


a.

Disconnect the fuel injector assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C14-1 - Body ground Power switch on (IG) 11 to 14 V
C15-1 - Body ground Power switch on (IG) 11 to 14 V
C16-1 - Body ground Power switch on (IG) 11 to 14 V
C17-1 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE

NG

12.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

13.CHECK FOR CAUSE OF FAILURE

NG

REPLACE FUEL INJECTOR ASSEMBLY

13.CHECK FOR CAUSE OF FAILURE
a.

If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.


b.

Check the intake valve for deposits.

HINT:

As the DTC may have been stored due to deposits an the intake valve, remove the cylinder head and check the intake valves.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

HINT:

Perform the appropriate confirmation driving patterns for the DTCs that were output.



b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
NEXT



NEXT

END