Home › Engine / Hybrid System › 2ZR-FXE COOLING › EXHAUST PIPE GAS CONTROL ACTUATOR
RM3210E _51 Engine / Hybrid System _047499 2ZR-FXE COOLING _0236580 EXHAUST PIPE GAS CONTROL ACTUATOR A

2ZR-FXE COOLING  EXHAUST PIPE GAS CONTROL ACTUATOR  REMOVAL  


PROCEDURE

Hide 51444C 1.REMOVE REAR MOTOR UNDER COVER LH

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 17495 3.REMOVE EXHAUST PIPE GAS CONTROL ACTUATOR

CAUTION:
·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



a.
A376891C01
2.271,1.01 2.563,1.792 2.563,1.792 2.771,1.792 true 1.938,1.01 2.292,0.458 2.292,0.458 2.5,0.458 true 1.854,1.271 1.729,2.031 1.729,2.031 1.531,2.031 true 1.594,1 1.375,0.417 1.375,0.417 1.177,0.417 true 2.521,0.375 2.729,0.552 0.208,0.177 10 true *a 2.792,1.708 2.99,1.896 0.198,0.188 10 true *b 1.302,1.948 1.521,2.135 0.219,0.188 10 true *1 0.969,0.354 1.188,0.542 0.219,0.188 10 true *2
*1 Outlet Heater Water Hose B
*2 Outlet Heater Water Hose C
*a No. 2 Outlet Water Pipe
*b Inlet Water Pipe


Slide the 2 clips and disconnect the outlet heater water hose B and outlet heater water hose C from the inlet water pipe and No. 2 outlet water pipe.


b.
A376856C02
2.49,1.5 2.948,1.5 true 2.396,0.76 2.531,0.76 2.531,0.76 2.677,1.01 true 2.323,1.406 2.51,1.604 0.188,0.198 10 true *a 2.219,0.688 2.406,0.865 0.188,0.177 10 true *b
*a Protective Tape
*b Spring


Using a screwdriver with the tip taped, pry the portion indicated in the illustration to disengage the spring.


c.
A376857C01
1.719,1.667 1.854,1.938 1.854,1.938 2.031,1.938 false 1.667,0.406 1.531,0.104 1.531,0.104 1.344,0.104 true 0.823,1.146 0.542,0.49 0.542,0.49 0.354,0.49 true 1.146,0.042 1.375,0.25 0.229,0.208 10 false *a 0.146,0.417 0.521,0.823 0.375,0.406 10 false *b 2.094,1.875 2.417,2.125 0.323,0.25 10 false *c
*a No. 1 Outlet Water Pipe
*b No. 2 Outlet Water Pipe
*c Inlet Water Pipe


Remove the 3 bolts and exhaust pipe gas control actuator sub-assembly and exhaust pipe gas control actuator gasket.

NOTICE:
·

When removing the exhaust pipe gas control actuator sub-assembly, use caution because coolant may spill out from the exhaust heat recirculation system.

·

Do not apply any excessive force to the No. 1 outlet water pipe, No. 2 outlet water pipe and inlet water pipe when removing the exhaust pipe gas control actuator sub-assembly.




d.
A376858C01
0.635,1.146 0.833,1.146 0.833,1.146 1.063,1.667 true 1.01,0.552 1.208,0.552 1.208,0.552 1.354,1.583 true 2.802,3 2.646,3 2.646,3 2.469,2.563 false 2.813,2.896 3.021,3.125 0.208,0.229 10 true *1 0.802,0.458 0.99,0.667 0.188,0.208 10 true *a 0.438,1.042 0.646,1.24 0.208,0.198 10 true *b
*1 Exhaust Pipe Gas Control Actuator
*a No. 2 Outlet Water Pipe
*b Inlet Water Pipe


While closing No. 2 outlet water pipe, apply compressed air to inlet water pipe to remove the exhaust pipe gas control actuator shown in the illustration.

HINT:

Use a piece of cloth to catch the exhaust pipe gas control actuator.