Home › Engine / Hybrid System › 2ZR-FXE COOLING › EXHAUST HEAT RECIRCULATION SYSTEM
RM3210E _51 Engine / Hybrid System _047499 2ZR-FXE COOLING _0236581 EXHAUST HEAT RECIRCULATION SYSTEM J

2ZR-FXE COOLING  EXHAUST HEAT RECIRCULATION SYSTEM  Exhaust Heat Recirculation System Circuit  


DESCRIPTION

In the exhaust heat recirculation system, coolant is warmed up using conventionally wasted exhaust gas heat to accelerate engine warm-up time, enhancing fuel efficiency and heater performance.

The heat recirculator is positioned in the front exhaust pipe assembly after the catalyst. Coolant from the engine flows around the heat recirculator and then returns to the engine. If the engine is started while the engine is cold, the exhaust pipe gas control actuator rod is contracted and the exhaust flow control valve is closed, routing the exhaust gas around the heat recirculator to warm up the coolant.

After the engine coolant temperature rises and the engine has warmed up, the heat of the coolant expands the thermostat and the exhaust pipe gas control actuator rod extends. This opens the exhaust flow control valve to switch to the normal exhaust gas path.

The exhaust flow control valve can also be opened by exhaust gas pressure to prevent insufficient acceleration performance when the engine is cold. In addition, to monitor the engine coolant temperature, an engine coolant temperature sensor (for exhaust heat recirculation system) is provided between the engine and the heat recirculator. The engine coolant temperature sensor (for exhaust heat recirculation system) has a built-in thermistor with a resistance that varies according to the temperature of the engine coolant. When the engine coolant temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the combination meter assembly as voltage changes. If the engine coolant temperature is excessively high (overheating), the water temperature indicator light in the meter circuit plates (combination meter assembly) illuminate to inform the driver of the malfunction.

A378487E02
4.021,1.417 3.688,0.75 3.688,0.75 3.438,0.75 true 2.667,2.552 2.667,2.135 true 3.375,2.698 3.667,2.333 3.667,2.333 3.917,2.333 true 5.333,3.75 6.417,4.083 6.417,4.083 6.417,4.25 true 4.75,4.25 5.5,4.917 5.5,4.917 5.75,4.917 true 4.583,4.917 4.333,4.917 4.333,4.917 4.333,4.24 true 4.083,4.333 3,4.667 3,4.667 3,4.917 true 2.25,7 1.75,7.75 1.75,7.75 1.75,7.917 true 5.417,7.167 5.167,7.75 5.167,7.75 5.167,7.917 true 4.135,3.5 3.667,3.833 3.667,3.833 3.417,3.833 true 2.167,6.167 1.917,6.167 1.917,6.167 1.667,6.438 true 5.75,6.167 5.5,6.167 5.5,6.167 5.25,6.438 true 3.26,0.667 3.542,0.927 0.281,0.26 10 false *3 1.677,1.521 2.125,1.823 0.448,0.302 10 false *1 2.594,2.583 2.802,2.813 0.208,0.229 10 false *5 3.969,2.271 4.885,2.469 0.917,0.198 10 false *6 5.854,2.115 6.115,2.323 0.26,0.208 10 false *7 6.01,3.302 6.625,3.5 0.615,0.198 10 false *b 1.313,3.198 1.927,3.396 0.615,0.198 10 false *2 6.344,4.271 6.552,4.49 0.208,0.219 10 false *8 5.813,4.854 6.271,5.052 0.458,0.198 10 false *d 4.656,4.833 4.906,5.031 0.25,0.198 10 false *c 2.906,4.979 3.198,5.219 0.292,0.24 10 false *4 0.24,5.781 3.156,5.979 2.917,0.198 10 false Exhaust Flow Control Valve Open: 3.74,5.781 6.406,5.979 2.667,0.198 10 false Exhaust Flow Control Valve Closed: 5.115,7.958 5.417,8.167 0.302,0.208 10 false *e 0.167,5.51 0.458,5.75 0.292,0.24 10 false *a 3.688,5.521 3.979,5.76 0.292,0.24 10 false *a 1.698,7.958 2,8.167 0.302,0.208 10 false *e 3.26,3.75 3.469,3.979 0.208,0.229 10 false *9 2.208,6.104 2.5,6.344 0.292,0.24 10 false *9 5.781,6.094 6.073,6.333 0.292,0.24 10 false *9

Text in Illustration
*1 Engine Assembly *2 Engine Coolant
*3 Engine Coolant Temperature Sensor (for Exhaust Heat Recirculation System) *4 Exhaust Pipe Gas Control Actuator
*5 Front Catalyst *6 Rear Catalyst
*7 Meter Circuit Plate (Combination Meter Assembly) *8 Front Exhaust Pipe Assembly
*9 Heat Recirculator - -
*a Side View *b Exhaust Gas
*c Thermostat *d Rod
*e Exhaust Flow Control Valve - -

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - METER CIRCUIT PLATE (COMBINATION METER ASSEMBLY))
a.

Disconnect the A10 engine coolant temperature sensor (for exhaust heat recirculation system) connector.


b.

Disconnect the F6 meter circuit plate (combination meter assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A10-2 (TWS3) - F6-23 (TWS3) Always Below 1 Ω
A10-1 (E2) - F6-3 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A10-2 (TWS3) or F6-23 (TWS3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR EXHAUST HEAT RECIRCULATION SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - METER CIRCUIT PLATE (COMBINATION METER ASSEMBLY))

2.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR EXHAUST HEAT RECIRCULATION SYSTEM)
a.

Inspect the engine coolant temperature sensor (for exhaust heat recirculation system).

Click hereEngine / Hybrid System>2ZR-FXE COOLING>TEMPERATURE SWITCH>INSPECTION


Result:
Result
OK
NG



OK

REPLACE METER CIRCUIT PLATE (COMBINATION METER ASSEMBLY)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR EXHAUST HEAT RECIRCULATION SYSTEM)