Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1503  Exhaust Heat Management Warning Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly (meter circuit plate) detects a malfunction in the engine coolant temperature sensor that is connected to the combination meter assembly (meter circuit plate) via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1503 Exhaust Heat Management Warning Detected When IG voltage is 9.5 V or more and either of the following conditions is detected:
·

Engine coolant temperature sensor circuit open or shorted

·

Engine coolant temperature is 120°C (248°F) or more


·

Harness or connector

·

Engine coolant temperature sensor

·

Combination meter assembly (Meter circuit plate)


DTC stored w/ Exhaust Heat Recirculation System

HINT:

This DTC is for the engine coolant temperature sensor which is used to detect the engine coolant temperature for the exhaust heat recirculation system, not for the engine coolant temperature sensor which is used for the SFI system.


WIRING DIAGRAM

E230581E09
2.229,0.875 2.344,1.021 0.115,0.146 10 false 2 2.229,2.219 2.344,2.365 0.115,0.146 10 false 1 1.75,0.875 2.188,1.042 0.438,0.167 10 false TSW3 1.958,2.219 2.177,2.375 0.219,0.156 10 false E2 0.625,3 1.042,3.302 0.417,0.302 10 false A10 0.615,3.146 2.396,3.5 1.781,0.354 10 false Engine Coolant Temperature Sensor 5.052,2.938 5.333,3.115 0.281,0.177 10 false F6 5.063,3.073 6.896,3.469 1.833,0.396 10 false Combination Meter Assembly (Meter Circuit Plate) 5.323,0.885 5.521,1.052 0.198,0.167 10 false 23 5.573,0.969 6.021,1.135 0.448,0.167 10 false TWS3 5.375,2.219 5.573,2.365 0.198,0.146 10 false 3 5.563,2.323 5.792,2.5 0.229,0.177 10 false E2

PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature 0 to 127.5°C (0 to 261.5°F) 75 to 100°C (167 to 212°F) (After warming up engine) -
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10
OK:

Engine coolant temperature displayed on the GTS is 75 to 100°C (167 to 212°F) after the engine is warmed.


NOTICE:

If the engine coolant temperature exceeds 100°C, the cooling system is malfunctioning. Stop the engine immediately.


HINT:

The coolant temperature value in this inspection is the data sent from the engine coolant temperature sensor for the SFI system.


Click here


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - ENGINE COOLANT TEMPERATURE SENSOR)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Disconnect the A10 engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-23 (TWS3) - A10-2 (TSW3) Always Below 1 Ω
F6-3 (E2) - A10-1 (E2) Always Below 1 Ω
F6-23 (TWS3) or A10-2 (TSW3) - Body ground Always 10 kΩ or higher
F6-3 (E2) or A10-1 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Remove the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE COOLING>TEMPERATURE SWITCH>REMOVAL


b.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2ZR-FXE COOLING>TEMPERATURE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR