Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM3210E _54 Brake _047520 BRAKE (FRONT) _0237141 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C344515C02
1.896,1 2.906,1 true 1.896,1.052 2.552,1.052 2.552,1.052 2.552,1 true 2.948,0.927 3.26,1.083 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C344534C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 47715A 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C344536C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side).


b.

Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (lower side).


c.
C344537C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the 2 front disc brake cylinder slide pins.


d.

Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.


e.

Push each front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.



Hide 04945 6.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn front disc brake pads, the front disc brake anti-squeal shims and front disc brake pad wear indicator plates must be replaced together with the front disc brake pads.

·

Do not apply disc brake grease to the lining surface of the brake pad.

·

Install the front disc brake pad wear indicator plates in the correct position and direction.

·

Install the front disc brake anti-squeal shims in the correct position and direction.



a.
C344535C02
0.438,0.26 0.75,0.417 0.313,0.156 10 false *A 0.438,1.917 0.75,2.073 0.313,0.156 10 false *B
*A Inside of the Vehicle
*B Outside of the Vehicle
V100155

Disc Brake Grease


Apply disc brake grease to both sides of each front No. 1 disc brake anti-squeal shim as shown in the illustration.


b.
C344538C02
1.531,0.74 1.531,0.594 1.531,0.594 2.656,0.594 false 2.323,1.156 2.323,0.594 false 0.792,0.375 0.906,0.375 0.906,0.375 1.031,1.042 false 0.417,1.448 0.542,2.281 0.542,2.281 0.656,2.281 false 2.573,3.24 2.677,3.24 2.677,3.24 2.906,2.917 false 2.688,2.01 2.948,1.531 2.948,1.531 3.031,1.531 false 0.625,0.313 0.938,0.469 0.313,0.156 10 false *1 0.698,2.219 1.01,2.375 0.313,0.156 10 false *2 2.708,0.531 3.021,0.688 0.313,0.156 10 false *3 2.396,3.167 2.708,3.323 0.313,0.156 10 false *2 3.073,1.469 3.385,1.625 0.313,0.156 10 false *1
*1 Front No. 1 Disc Brake Anti-squeal Shim
*2 Front No. 2 Disc Brake Anti-squeal Shim
*3 Front Disc Brake Pad Wear Indicator Plate


Install the front No. 1 disc brake anti-squeal shim and front No. 2 disc brake anti-squeal shim to each front disc brake pad.


c.

Install the front disc brake pad wear indicator plate to each front disc brake pad.


Hide 7.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




Hide 47750 8.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47313J 9.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
33.3 N*m (340 kgf*cm, 25 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


c.

Perform the following procedure if air bleeding is not necessary:

i.

Turn the power switch on (READY).


ii.

Depress the brake pedal and release it.




Hide 11.BLEED BRAKE LINE

Hide 12.INSTALL FRONT WHEEL