Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM3210E _54 Brake _047520 BRAKE (FRONT) _0237141 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



b.
C342086C01
0.083,0.073 0.313,0.271 0.229,0.198 10 true *A 0.083,2.406 0.313,2.604 0.229,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the reservoir level switch connector with the parking brake applied.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>REMOVAL


d.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


e.

Check that the brake pedal cannot be further depressed.


f.

Release the parking brake.


Hide 3.REMOVE FRONT WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47313J 5.DISCONNECT FRONT FLEXIBLE HOSE

a.
C344506

Remove the union bolt and gasket, and disconnect the front flexible hose from the front disc brake cylinder assembly.


Hide 47750 6.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY

a.
C344507C02
1.781,1.604 2.094,1.76 0.313,0.156 10 false *a 2.313,1.667 2.625,1.823 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 front disc brake cylinder slide pins and remove the 2 bolts and front disc brake cylinder assembly.


Hide 7.REMOVE FRONT DISC BRAKE PAD

a.
C344508

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 04945 8.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

Remove the front No. 1 disc brake anti-squeal shim and front No. 2 disc brake anti-squeal shim from each front disc brake pad.


b.
C344509

Using a screwdriver, remove the front disc brake pad wear indicator plate from each front disc brake pad.


Hide 9.REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C344510

Remove the 4 front disc brake pad support plates from the front disc brake cylinder mounting.

NOTICE:

Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47715A 10.REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C344511

Remove the 2 front disc brake cylinder slide pins from the front disc brake cylinder mounting.


b.
C344512C02
2.188,1.427 2.406,0.865 2.406,0.865 2.5,0.865 false 2.552,0.792 2.865,0.948 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the front disc brake cylinder slide bushing from the front disc brake cylinder slide pin (lower side).

NOTICE:

Do not damage the front disc brake cylinder slide pin.



Hide 11.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT

a.
C344513

Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.


Hide 47722 12.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING

a.
C344514

Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.


Hide 43512 13.REMOVE FRONT DISC

a.
C344515C02
1.896,1 2.906,1 true 1.896,1.052 2.552,1.052 2.552,1.052 2.552,1 true 2.948,0.927 3.26,1.083 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front disc and the front axle hub sub-assembly.


b.

Remove the front disc.