Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM3210E _58 Vehicle Interior _047513 DOOR LOCK _0237310 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 69780B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B432438C01
1.802,0.885 1.896,1.031 false
V113147

Install in this Direction


Install the rear door inside locking cable assembly as shown in the illustration.


b.
B432436

Engage the 4 claws to close the cover as shown in the illustration.


Hide 69740D 3.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B432434C01
2.146,1.115 2.188,1.198 false
V113147

Install in this Direction


Install the rear door lock remote control cable assembly as shown in the illustration.


b.
B432432

Engage the 2 claws to close the cover as shown in the illustration.


Hide 69780B 4.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B432404C01
1.875,1.021 1.823,0.917 false
V113147

Install in this Direction


Install the rear door inside locking cable assembly as shown in the illustration.


b.
B432400

Engage the 5 claws to close the cover as shown in the illustration.


Hide 69740D 5.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B432396C01
2.198,0.625 2.281,0.76 false
V113147

Install in this Direction


Install the rear door lock remote control cable assembly as shown in the illustration.


b.
B424094

Engage the 2 claws to close the cover as shown in the illustration.


Hide 69060A 6.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B432429C01
3.156,2.958 3.271,2.729 false 3.083,2.969 3.281,3.146 0.198,0.177 10 true *a 0.521,1.917 0.896,2.156 0.375,0.24 12 false *A 1.552,1.917 1.927,2.156 0.375,0.24 12 false *B 0.167,2.167 0.323,2.365 0.156,0.198 10 false a 0.167,2.604 0.323,2.802 0.156,0.198 10 false b 1.188,2.219 1.344,2.417 0.156,0.198 10 false c 1.188,2.635 1.344,2.833 0.156,0.198 10 false d
*A for Type A
*B for Type B
*a Release Plate
V113147

Install in this Direction


Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.

HINT:

Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
for Type A : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
for Type B : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

Area Measurement
a 5.25 to 5.55 mm (0.207 to 0.219 in.)
b 16.5 to 17.1 mm (0.650 to 0.673 in.)
c 5.9 to 6.5 mm (0.232 to 0.256 in.)
d 14.0 to 15.0 mm (0.551 to 0.591 in.)


e.

Connect the connector.


Hide 68104 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 68124B 8.INSTALL REAR DOOR QUARTER WINDOW GLASS

Hide 67408E 9.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 67872 10.CONNECT REAR DOOR WEATHERSTRIP

a.

Connect the rear door weatherstrip.


Hide 68152C 11.INSTALL REAR DOOR GLASS RUN

Hide 67844A 12.INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

Hide 67858B 13.INSTALL REAR DOOR PANEL PROTECTOR

Hide 67842E 14.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 15.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL

Hide 67604 16.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 17.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Hide 74260 18.INSTALL REAR ARMREST ASSEMBLY

Hide 69284G 19.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 20.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 21. INITIALIZE POWER WINDOW CONTROL SYSTEM