Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM3210E _59 Vehicle Exterior _047505 DOOR / HATCH _0244374 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75989C 3.INSTALL REAR DOOR UPPER OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75988C 4.INSTALL REAR DOOR OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75978H 5.INSTALL REAR DOOR LOWER OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75766A 6.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75764A 7.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75762A 8.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75740 9.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 67896 10.INSTALL REAR DOOR NO. 3 WEATHERSTRIP

a.

Clean the rear door panel.


b.

Remove the release paper from a new rear door No. 3 weatherstrip.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B436669C01
0.979,2.979 0.948,2.979 false
V100155

Double-sided Tape


Engage the claw and install the rear door No. 3 weatherstrip.


Hide 67837C 11.INSTALL REAR DOOR DUST PROOF SEAL

a.
B436668

Engage the 3 claws to install 3 new rear door dust proof seals.


Hide 67003C 12.INSTALL REAR DOOR PANEL CUSHION

a.
B436667

Engage the 2 claws to install a new rear door panel cushion.


Hide 69204A 13.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B436666C01
0.083,0.083 0.344,0.281 0.26,0.198 12 true *A 0.083,2.583 0.344,2.781 0.26,0.198 12 true *B
*A Outside
*B Inside


Engage the claw as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 14.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B436664

Engage the 3 guides and claw to install the rear door rear outside handle pad.


Hide 69241G 15.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B436663

Engage the 3 claws to install the rear door front outside handle pad.


Hide 69227L 16.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B436662

Engage the claw.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69240 17.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B436661C01
1.052,0.781 1.125,0.719 false
V113147

Install in this Direction


Insert the front end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly.


b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly, then slide the rear door outside handle assembly toward the front of the vehicle to install it.


c.
B436659

Move the lever as shown in the illustration and engage the 2 claws to secure the rear door outside handle assembly.


Hide 69060A 18.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 19.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Temporarily install the temporary bolt to the rear door window regulator assembly.


c.
B442173C01
1.292,0.313 1.698,0.625 true 1.052,0.208 1.302,0.448 0.25,0.24 10 true *a 2.063,1.563 2.271,1.792 0.208,0.229 10 true 1 2.698,0.063 2.906,0.292 0.208,0.229 10 true 2 2.677,1.354 2.885,1.583 0.208,0.229 10 true 3 1.969,0.115 2.177,0.344 0.208,0.229 10 true 4
*a Temporary Bolt


Temporarily install the rear door window regulator assembly with the 3 bolts.


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69975A 20.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B436654C01
0.552,1.01 0.25,0.833 false 3.083,1.01 3.208,0.917 false 0.979,0.125 1.354,0.365 0.375,0.24 12 false *A 2.125,0.125 2.5,0.365 0.375,0.24 12 false *B 0.573,0.448 0.729,0.646 0.156,0.198 10 false A 3.01,0.438 3.167,0.635 0.156,0.198 10 false B 0.073,0.708 0.385,0.906 0.313,0.198 10 false *a 3.229,0.792 3.406,0.969 0.177,0.177 10 false *a
*A Front Side
*B Rear Side
*a Edge of curved surface


Install the rear door glass channel filler to the rear door glass sub-assembly at position shown in the illustration.

Standard Dimension
Area Measurement
A 5.0 mm (0.197 in.)
B 5.0 mm (0.197 in.)


Hide 69906B 21.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.

Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.


b.
B436655C01
0.208,1.031 0.458,1.198 false 3.083,1.198 3.208,1.115 false 1,0.115 1.375,0.354 0.375,0.24 12 false *A 2.125,0.115 2.5,0.354 0.375,0.24 12 false *B 3,0.51 3.156,0.708 0.156,0.198 10 false B 0.479,0.531 0.635,0.729 0.156,0.198 10 false A 0.031,0.896 0.344,1.094 0.313,0.198 10 false *a 3.229,0.979 3.417,1.167 0.188,0.188 10 false *a
*A Front Side
*B Rear Side
*a Edge of curved surface


Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

Standard Dimension
Area Measurement
A 5.0 mm (0.197 in.)
B 5.0 mm (0.197 in.)

NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.



Hide 68104 22.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B442176C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



b.
B436652

Slide the rear door glass sub-assembly to install it as shown in the illustration.


Hide 68124B 23.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.

Install the rear door quarter window glass to the rear door quarter window weatherstrip.


b.
B439195C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.


Hide 67408E 24.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B436649C01
1.688,0.313 1.688,0.26 false
V100135

Screw
V100136

Bolt


Install the rear door window division bar sub-assembly with the screw and 2 bolts.

Torque:
Screw : 3.1 N*m (32 kgf*cm, 27 in.*lbf)
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 67872 25.INSTALL REAR DOOR WEATHERSTRIP

a.

Clean the rear door panel.


b.

Remove the release paper from a new rear door weatherstrip.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B436644C01
0.354,1.271 0.76,1.104 true 0.385,1.552 0.708,1.74 true 0.781,0.979 0.969,1.146 0.188,0.167 10 true *a 0.729,1.677 0.917,1.844 0.188,0.167 10 true *a
*a Double-sided Tape


Engage the 25 clips and install the rear door weatherstrip.


Hide 68640A 26.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.

Clean the bolt hole in the vehicle body.


c.

Clean the threads of the bolt (B).


d.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
B436643N01
1.51,0.396 1.667,0.594 0.156,0.198 10 true A 1.5,1.469 1.656,1.667 0.156,0.198 10 true A 2.198,1.521 2.354,1.719 0.156,0.198 10 true B

Install the rear door check assembly with the 3 bolts.

Torque:
Bolt (A) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 68152C 27.INSTALL REAR DOOR GLASS RUN

a.
B436648

Install the rear door glass run.


Hide 67844A 28.INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

a.
B436647

Install the rear door No. 2 service hole cover.


Hide 67858B 29.INSTALL REAR DOOR PANEL PROTECTOR

a.
B436646

Install the rear door panel protector.


Hide 67842E 30.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.
B436642C01
0.26,0.302 0.396,0.385 true 3.031,0.375 3.146,0.292 true 2.99,3.021 3.125,3.063 true 0.094,0.167 0.271,0.344 0.177,0.177 10 true *a 3.156,0.156 3.333,0.333 0.177,0.177 10 true *a 3.146,2.958 3.323,3.135 0.177,0.177 10 true *a
*a Reference Point


Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.


c.

Attach the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 67674A 31.INSTALL REAR DOOR FRAME GARNISH

a.
B436640

Engage the 2 claws to install the rear door frame garnish.


Hide 86160B 32.INSTALL REAR SPEAKER ASSEMBLY

Hide 69206C 33.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B436639

Engage the 2 claws to install the rear door inside handle sub-assembly.


Hide 67848B 34.INSTALL REAR DOOR NO. 2 VENT SEAL

a.
B442195C02
0,0 0,0 false
V113147

Install in this Direction


Install the rear door No. 2 vent seal to the front door inner glass weatherstrip.


Hide 35.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL

a.
B436636C01
1.76,0.667 1.781,0.75 false
V113147

Install in this Direction


Install the rear door inner glass weatherstrip with rear door No. 2 vent seal as shown in the illustration.


Hide 67604 36.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B436638C01
1.844,0.792 1.833,0.688 false
V113147

Install in this Direction


Install the No. 1 door scuff plate clamp as shown in the illustration.


b.
B436634C01
2.208,1.688 2.354,1.656 false 2.75,1.219 3.031,0.927 false 2.854,1.802 2.635,1.552 false 3.042,0.823 3.313,1.021 0.271,0.198 10 true *1 2.865,1.76 3.135,1.958 0.271,0.198 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle sub-assembly as shown in the illustration.


c.
B436632

Engage the 6 claws and guide.


d.

Engage the 8 clips to install the rear door trim board sub-assembly.


e.
B436630

Install the 3 screws.


Hide 37.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.

Connect the connector.


b.
B436629C01
1.708,0.625 1.708,0.417 false
V113147

Install in this Direction


Engage the 2 clips and 2 claws to install the rear power window regulator switch assembly with rear door upper armrest base panel as shown in the illustration.


Hide 74260 38.INSTALL REAR ARMREST ASSEMBLY

a.
B436627C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 clips and 7 claws to install the rear armrest assembly as shown in the illustration.


Hide 69284G 39.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B436625

Engage the 3 claws to install the rear door inside handle bezel plug.


Hide 40.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 41. INITIALIZE POWER WINDOW CONTROL SYSTEM