Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)
RM3210E _58 Vehicle Interior _047538 SEAT BELT _0237552 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects rear seat belt state. The rear seat belt warning light on the combination meter assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

B442689E01
0.646,6.458 4.313,6.656 3.667,0.198 10 false : CAN Communication Line 0.208,5.75 1.833,6.135 1.625,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 0.219,5.604 1.25,5.885 1.031,0.281 10 false MB 1.5,4.094 2.24,4.323 0.74,0.229 10 false LCTY 1.479,5.156 2.219,5.385 0.74,0.229 10 false RCTY 1.906,5.042 2.646,5.271 0.74,0.229 10 false 2 1.906,3.969 2.646,4.198 0.74,0.229 10 false 13 3.729,4.427 4.469,4.656 0.74,0.229 10 false M12 3.74,5.458 4.479,5.688 0.74,0.229 10 false M52 3.719,4.563 6.917,4.844 3.198,0.281 10 false Rear Door Courtesy Light Switch Assembly (for LH) 3.729,5.615 6.927,5.917 3.198,0.302 10 false Rear Door Courtesy Light Switch Assembly (for RH) 4.615,3.969 5.354,4.198 0.74,0.229 10 false 1 4.635,5.042 5.375,5.271 0.74,0.229 10 false 1 2.167,0.625 2.906,0.854 0.74,0.229 10 false RRSB 2.167,1.885 2.906,2.115 0.74,0.229 10 false RCSB 2.198,2.427 2.938,2.656 0.74,0.229 10 false RLSB 4.771,2.313 5.51,2.542 0.74,0.229 10 false LBR+ 4.771,1.792 5.51,2.021 0.74,0.229 10 false CBR+ 4.771,0.531 5.51,0.76 0.74,0.229 10 false RBR+ 5.948,0.531 6.688,0.76 0.74,0.229 10 false RBR- 5.969,1.792 6.708,2.021 0.74,0.229 10 false CBR- 5.99,2.313 6.729,2.542 0.74,0.229 10 false LBR- 4.469,1.115 6.667,1.51 2.198,0.396 10 false Rear Seat Inner Belt Assembly RH 4.708,2.844 6.417,3.302 1.708,0.458 10 false Rear Seat Inner with Center Belt Assembly LH 1.104,2.979 1.844,3.208 0.74,0.229 10 false F6 1.104,3.146 3.542,3.448 2.438,0.302 10 false Combination Meter Assembly 5.208,2.042 5.948,2.271 0.74,0.229 10 false (for Center) 5.323,2.542 6.063,2.771 0.74,0.229 10 false (for LH) 4.521,2.25 4.677,2.448 0.156,0.198 10 false 5 4.604,0.51 4.76,0.708 0.156,0.198 10 false 5 6.354,0.5 6.51,0.698 0.156,0.198 10 false 4 4.51,1.708 4.667,1.906 0.156,0.198 10 false 1 6.458,1.719 6.615,1.917 0.156,0.198 10 false 2 6.458,2.24 6.615,2.438 0.156,0.198 10 false 4 4.469,0.969 5.208,1.198 0.74,0.229 10 false M25 4.438,2.417 5.177,2.646 0.74,0.229 10 false M26 6.365,1.896 7.104,2.125 0.74,0.229 10 false M27 6.354,2.417 7.094,2.646 0.74,0.229 10 false M26 4.438,1.896 5.177,2.125 0.74,0.229 10 false M27 2.625,0.521 2.844,0.719 0.219,0.198 10 false 10 2.625,1.792 2.844,1.99 0.219,0.198 10 false 11 2.625,2.323 2.844,2.521 0.219,0.198 10 false 12 1.917,5.646 3.531,6.031 1.615,0.385 10 false Instrument Panel Junction Block Assembly 3.031,4.083 3.771,4.313 0.74,0.229 10 false 3H 3.042,3.885 3.781,4.115 0.74,0.229 10 false 24 3.031,5.156 3.771,5.385 0.74,0.229 10 false 3A 3.042,4.958 3.781,5.188 0.74,0.229 10 false 31 1.115,3.417 3.042,3.646 1.927,0.229 10 false - Meter Circuit Plate

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.READ VALUE USING GTS (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch RH ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch LH ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25

OK:

ON or OFF appears on the GTS screen according to the rear door condition.


Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT BELT WARNING

NG

2.CHECK REAR SEAT BELT WARNING
a.
B332796C01
1.135,1.635 1.135,1.354 false 1.708,1.635 1.708,1.354 false 2.302,1.635 2.302,1.354 false 0.229,0.156 0.458,0.385 0.229,0.229 10 *1 1.073,1.688 1.26,1.896 0.188,0.208 10 *a 1.646,1.688 1.917,1.906 0.271,0.219 10 *b 2.24,1.688 2.438,1.896 0.198,0.208 10 *c
*1 Rear Seat Belt Warning Light (Combination Meter Assembly)
*a LH
*b Center
*c RH


Check the rear seat belt warning function.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)>ON-VEHICLE INSPECTION

Result:
Result Proceed to
The rear seat belt warning lights operate normally A
The rear seat belt warning lights (all seats) do not operate normally B
The rear seat belt warning light (RH) does not operate normally C
The rear seat belt warning light (center) does not operate normally D
The rear seat belt warning light (LH) does not operate normally E




A

B

C

3.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH (FOR RH))

D

5.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER))

E

7.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH (FOR LH))
3.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH (FOR RH))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear RH seat belt buckle switch signal ON or OFF ON: Rear RH seat belt fastened
OFF: Rear RH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
50003 122 74

Result:
Result Proceed to
ON or OFF does not appear on the GTS screen according to the rear seat belt condition A
ON or OFF appears on the GTS screen according to the rear seat belt condition B



A

4.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - REAR SEAT INNER BELT ASSEMBLY RH - BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - REAR SEAT INNER BELT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the M25 rear seat inner belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-10 (RRSB) - M25-5 (RBR+) Always Below 1 Ω
F6-10 (RRSB) or M25-5 (RBR+) - Body ground Always 10 kΩ or higher
M25-4 (RBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (C) Rear center seat belt buckle switch signal ON or OFF ON: Rear center seat belt fastened
OFF: Rear center seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (C)
50003 122 76

Result:
Result Proceed to
ON or OFF does not appear on the GTS screen according to the rear seat belt condition A
ON or OFF appears on the GTS screen according to the rear seat belt condition B



A

6.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR CENTER) - BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR CENTER) - BODY GROUND)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the M27 rear seat inner with center belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-11 (RCSB) - M27-1 (CBR+) Always Below 1 Ω
F6-11 (RCSB) or M27-1 (CBR+) - Body ground Always 10 kΩ or higher
M27-2 (CBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH (FOR LH))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (L) Rear LH seat belt buckle switch signal ON or OFF ON: Rear LH seat belt fastened
OFF: Rear LH seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (L)
50003 122 75

Result:
Result Proceed to
ON or OFF does not appear on the GTS screen according to the rear seat belt condition A
ON or OFF appears on the GTS screen according to the rear seat belt condition B



A

8.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR LH) - BODY GROUND)

B

8.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR LH) - BODY GROUND)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the M26 rear seat inner with center belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-12 (RLSB) - M26-5 (LBR+) Always Below 1 Ω
F6-12 (RLSB) or M26-5 (LBR+) - Body ground Always 10 kΩ or higher
M26-4 (LBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR