This DTC is applicable to Euro-OBD and Brazil OBD only.
Refer to DTC P030000.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P030000
Refer to DTC P04019C.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P04019C
Refer to DTC P21951D.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P21951D
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P10AA00 | Clogged EGR Port Imbalance Bank1 | The difference in the air fuel ratios between the cylinders exceeds the threshold when the EGR valve is open (2 trip detection logic). | ·
Intake manifold ·
Fuel injector assembly ·
Intake system ·
Gas leaks from exhaust system ·
Ignition system ·
Compression pressure ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Does not come on | DTC stored | SAE Code: P10AA |
By comparing the air fuel ratio when EGR valve is open and closed, a clog in an EGR port can be detected. If the imbalance becomes larger when the EGR valve is open, the ECM will determine that the EGR port is clogged and store this DTC.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) [A].
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].
Turn the power switch off [C].
Turn the power switch on (READY).
Start the engine by depressing the accelerator pedal approximately 40% and accelerating the vehicle from 10 km/h (6 mph) to a speed between 50 and 60 km/h (31 to 37 mph) in 10 to 15 seconds [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the engine does not start, further depress the accelerator pedal.
Decelerate the vehicle to less than 10 km/h (6 mph) and allow the engine to stop [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
The vehicle can be decelerated by any method.
Repeat steps [D] and [E] above 15 to 20 times [F].
Enter the following menus: Powertrain / Engine / Trouble Codes [G].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P10AA00.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to Fuel Injector Circuit.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
When any air fuel ratio imbalance is detected, the ECM will perform air fuel ratio feedback control to make the air fuel ratio close to the stoichiometric level. This may result in an air fuel ratio imbalance of normal cylinders and DTCs may be stored.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P10AA00 is output | A |
| DTC P10AA00 and other DTCs are output | B |
If any DTCs other than DTC P10AA00 are output, troubleshoot those DTCs first.
A
B
Replace the intake manifold.
Click hereEngine / Hybrid System>2ZR-FXE INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL
Perform "Inspection After Repair" after replacing the intake system.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P10AA00 is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up.
The A/C switch and all accessories should be off and park (P) or neutral (N) should be selected.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / Misfire Count Cylinder #1 to #4.
When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 7 (Check Intake System).
| Active Test Display |
|---|
| Control the Injection Volume |
| Data List Display |
|---|
| Misfire Count Cylinder #1 |
| Misfire Count Cylinder #2 |
| Misfire Count Cylinder #3 |
| Misfire Count Cylinder #4 |
According to the display on the GTS, perform the Active Test with the engine idling.
Check the misfire counts (Misfire Count Cylinder #1 to #4) while decreasing the injection volume in 5% increments.
The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Check for exhaust gas leaks.
No gas leaks in exhaust system.
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2ZR-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spark plug of the cylinder causing the imbalance.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Disconnect the fuel injector assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| C15-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| C16-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| C17-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
Check the intake valve for deposits.
As the DTC may have been stored due to deposits on an intake valve, remove the cylinder head and check the intake valves.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
DTCs are not output.
| Proceed to |
|---|
| NEXT |
NEXT