Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0238440 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horns to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B424476E06
0.823,0.156 2.656,0.354 1.833,0.198 10 false from Auxiliary Battery 2.333,1.865 2.948,2.063 0.615,0.198 10 false HORN 1.104,1.094 1.719,1.292 0.615,0.198 10 false HORN 6.115,0.844 6.729,1.042 0.615,0.198 10 false HORN 1.031,2.281 3.292,2.875 2.26,0.594 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly 2.573,4.76 3.708,5.125 1.135,0.365 10 false Low Pitched Horn Assembly 4.198,4.75 5.344,5.125 1.146,0.375 10 false High Pitched Horn Assembly 4.438,1.917 6.052,2.323 1.615,0.406 10 false Instrument Panel Junction Block Assembly 5.375,3.396 7.052,3.927 1.677,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 2.021,0.844 2.24,1.042 0.219,0.198 10 false 1 2.031,1.448 2.25,1.646 0.219,0.198 10 false 3 2.938,0.833 3.156,1.031 0.219,0.198 10 false 2 2.938,1.448 3.156,1.646 0.219,0.198 10 false 5 2.26,4.5 2.479,4.698 0.219,0.198 10 false 1 3.875,4.521 4.094,4.719 0.219,0.198 10 false 1 2.594,4.583 2.948,4.781 0.354,0.198 10 false A1 4.198,4.573 4.552,4.771 0.354,0.198 10 false A3 4.792,4.031 7.104,4.25 2.313,0.219 10 false to Steering Pad Switch Assembly 5.865,0.823 6.219,1.021 0.354,0.198 10 false 28 5.365,3.208 5.719,3.406 0.354,0.198 10 false MB 6.74,1.021 7.094,1.219 0.354,0.198 10 false IC 4.635,0.729 4.99,0.927 0.354,0.198 10 false 27 4.625,0.948 4.979,1.146 0.354,0.198 10 false 3F 4.625,1.24 4.979,1.438 0.354,0.198 10 false 50 4.615,1.448 4.969,1.646 0.354,0.198 10 false 3A

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.INSPECT HORNS
a.

Press the horn switch and check if the horns sound.

Result:
Result Proceed to
Horns sound A
Horns do not sound B




A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B424477C03
1.396,0.292 1.688,0.51 0.292,0.219 4.896,0.5 5.167,0.74 0.271,0.24 6.271,1.083 6.271,1.406 6.271,1.406 5.833,1.406 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.458,0.323 1.771,0.521 0.313,0.198 10 false 3F 4.927,0.531 5.24,0.729 0.313,0.198 10 false MB 5.427,1.323 5.99,1.542 0.563,0.219 10 false HORN
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-27 - MB-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY