Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0238440 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Power Source Circuit  


DESCRIPTION

Based on changes in the power source voltage, the main body ECU (multiplex network body ECU) can detect if the auxiliary battery has been disconnected and reconnected.

WIRING DIAGRAM

B438178E03
0.813,0.823 2.292,1.146 1.479,0.323 10 false from Auxiliary Battery 3.427,0.854 3.771,1.073 0.344,0.219 10 false 3F 3.469,0.667 3.813,0.885 0.344,0.219 10 false 1 4.156,1 5.385,1.24 1.229,0.24 10 false ECU-DCC NO. 2 3.688,1.531 5.302,1.979 1.615,0.448 10 false Instrument Panel Junction Block Assembly 5.469,1.958 7.156,2.469 1.688,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,1.792 5.813,2.01 0.344,0.219 10 false MB 5.656,0.844 6.625,1.115 0.969,0.271 10 false BECU 5.406,0.74 5.75,0.958 0.344,0.219 10 false 31

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SUPPLY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Power switch off 8.5 V or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B439647C03
1.521,0.75 1.875,0.99 0.354,0.24 4.896,0.75 5.25,0.99 0.354,0.24 6.458,2.094 6.635,2.094 6.635,2.094 6.635,1.604 false 1.604,0.771 1.917,0.969 0.313,0.198 10 false 3F 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 4.969,0.771 5.281,0.969 0.313,0.198 10 false MB 6.052,2.01 6.656,2.271 0.604,0.26 10 false BECU
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-1 - MB-31 (BECU) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY