Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0239264 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AA1  FCM Destination Information Unmatched  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store country specification information received from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU. If the country specification information stored in the forward recognition camera is different from that stored in the main body ECU (multiplex network body ECU) or hybrid vehicle control ECU, DTC C1AA1 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA1 FCM Destination Information Unmatched 2 seconds after the power switch is turned on (IG), destination information stored in the forward recognition camera and that received from the main body ECU (multiplex network body ECU) or hybrid vehicle control ECU do not match for 5 seconds or more.
·

CAN communication system

·

Forward recognition camera

·

Main body ECU (Multiplex network body ECU)

·

Hybrid vehicle control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT



HINT:

This DTC is stored when the destination information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) do not match. If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.


PROCEDURE

1.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
HINT:

When DTC C1AA1 is stored, lane departure alert system DTC C1AAC may be stored at the same time.


a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AAC is not output A
DTC C1AAC is output B



A

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

B

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC U0142 is not output A
DTC U0142 is output B



A

3.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

B

3.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA1 is not output A
DTC C1AA1 is output B



A

B

4.REPLACE FORWARD RECOGNITION CAMERA
4.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
5.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA1 is not output A
DTC C1AA1 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)