Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0239265 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1A01  Driving Support ECU  


DESCRIPTION

If the forward recognition camera detects a malfunction in the internal circuit of the driving support ECU assembly, DTC C1A01 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A01 Driving Support ECU 2 seconds after the power switch is turned on (IG), a malfunction in the driving support ECU assembly internal circuit is detected for 5 seconds or more.
·

Driving support ECU assembly

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The lane departure alert system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
HINT:

When the lane departure alert system outputs DTC C1A01, the pre-crash safety system may also output DTC C1A01. If DTC C1A01 is output, perform diagnosis for the pre-crash safety system first.


a.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A01 is not output A
DTC C1A01 is output B



A

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A01 is not output A
DTC C1A01 is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A01 is not output A
DTC C1A01 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY