Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0239265 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The forward recognition camera uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the forward recognition camera detects this, and stores DTC C1A11.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A11 Front Radar Sensor Incorrect Axial Gap 2 seconds after the power switch is turned on (IG), misalignment of the millimeter wave radar sensor assembly is detected for approximately 5 seconds.
·

Millimeter wave radar sensor assembly

·

Forward recognition camera


C1A14 Front Radar Sensor Beam Axis Not Adjusted 2 seconds after the power switch is turned on (IG), incompletion of the millimeter wave radar sensor beam axis alignment is detected for approximately 5 seconds.
·

Millimeter wave radar sensor assembly

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

The lane departure alert system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
Current DTC C1A11 is output A
Current DTC C1A14 is output B
History DTC C1A11 is output C



A

2.CHECK VEHICLE CONDITION

B

11.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

C

13.CLEAR DTC (LANE DEPARTURE ALERT SYSTEM)
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or has been towed. A
Vehicle is overloaded or has been towed. B



A

3.CHECK WHEEL ALIGNMENT

B

9.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).

for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front or rear wheel is misaligned (toe) A
Front and rear wheels are not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

7.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.ADJUST WHEEL ALIGNMENT

Result:
Proceed to
NEXT



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
6.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
HINT:

After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the forward recognition camera.


a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA

7.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed.

HINT:

When the bracket is deformed, replace the millimeter wave radar sensor assembly.


OK:

The bracket is not deformed.



Result:
Proceed to
OK
NG



OK

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
9.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Return the vehicle to normal operating conditions.


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
10.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END

B

3.CHECK WHEEL ALIGNMENT
11.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
12.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
HINT:

After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the forward recognition camera.


a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA

13.CLEAR DTC (LANE DEPARTURE ALERT SYSTEM)
a.

Check for DTCs related to misalignment of millimeter wave radar sensor assembly.

HINT:

If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.



b.

Result:
Proceed to
NEXT



NEXT

END