Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A46  Yaw Rate Sensor  


DESCRIPTION

The driving support ECU assembly receives yaw rate sensor signals from the yaw rate sensor (airbag ECU assembly) and skid control ECU (brake booster with master cylinder assembly) via CAN communication. If the driving support ECU assembly receives a yaw rate sensor malfunction signal from the yaw rate sensor (airbag ECU assembly) or skid control ECU (brake booster with master cylinder assembly), DTC C1A46 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A46 Yaw Rate Sensor
·

While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor malfunction signal from yaw rate sensor for approximately 10 seconds.

·

While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor zero point malfunction signal from skid control ECU (brake booster with master cylinder assembly) for approximately 10 seconds.


·

Electronically controlled brake system

·

Yaw rate sensor (Airbag ECU assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Pre-crash safety system DTC C1A46 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output B



A

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

5.REPLACE YAW RATE SENSOR (AIRBAG ECU ASSEMBLY)
5.REPLACE YAW RATE SENSOR (AIRBAG ECU ASSEMBLY)
a.

Replace the yaw rate sensor (airbag ECU assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
6.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output B



A

END (YAW RATE SENSOR WAS DEFECTIVE)

B

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)