Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A47  Steering Angle Sensor  


DESCRIPTION

The driving support ECU assembly receives steering angle information from the steering sensor. If the driving support ECU assembly detects a steering sensor malfunction, DTC C1A47 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A47 Steering Angle Sensor While the vehicle is being driven at a speed of 50 km/h (32 mph) or more, the driving support ECU assembly receives a steering sensor malfunction signal continuously for 1 second or more.
·

Electronically controlled brake system

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Pre-crash safety system DTC C1A47 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output B



A

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)