Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The driving support ECU assembly operates the pre-crash warning by sending a buzzer request signal to the skid control buzzer.

If the driving support ECU assembly detects a malfunction in the skid control buzzer circuit, it will store DTC C1A4A.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit When the power switch is on (IG) and the pre-crash warning is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the skid control buzzer but the buzzer sounds for 1 second or more.


·

Skid control buzzer

·

Driving support ECU assembly

·

Wire harness or connector



WIRING DIAGRAM

B403796E67
5.031,2.073 6.958,2.271 1.927,0.198 10 false Driving Support ECU Assembly 3.281,1.156 4.646,1.385 1.365,0.229 10 false Skid Control Buzzer 2.052,0.844 3.74,1.042 1.688,0.198 10 false ECU-IG1 NO. 4 3.583,0.698 4.042,0.896 0.458,0.198 10 false IG1 5.521,0.698 5.979,0.896 0.458,0.198 10 false BZ 4.24,0.698 4.552,0.896 0.313,0.198 10 false BZ 3.292,1 3.802,1.24 0.51,0.24 10 false F41 5.042,1.906 5.5,2.104 0.458,0.198 10 false F40 4.5,0.594 4.656,0.792 0.156,0.198 10 false 1 3.406,0.594 3.563,0.792 0.156,0.198 10 false 2 5.365,0.604 5.521,0.802 0.156,0.198 10 false 3 0.135,0.688 2.125,0.885 1.99,0.198 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with power switch on (IG), vehicle stopped
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C01
1.5,0.177 1.906,0.438 0.406,0.26 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.583,0.229 2.042,0.427 0.458,0.198 10 false F41 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the F41 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F41-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



c.

Connect the F41 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - AUXILIARY BATTERY)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F41 skid control buzzer connector.


b.

Disconnect the F40 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-1 (BZ) - F40-3 (BZ) Always Below 1 Ω
F41-1 (BZ) or F40-3 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the F40 driving support ECU assembly connector.


e.

Connect the F41 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with power switch on (IG), vehicle stopped
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the power switch on (IG).


b.

Check if the skid control buzzer is sounding.


Result:
Result Proceed to
The skid control buzzer does not sound when the power switch is on (IG) A
The skid control buzzer sounds continuously when the power switch is on (IG) B



A

7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER
7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)


Result:
Result Proceed to
Skid control buzzer is abnormal A
Skid control buzzer is normal B



A

8.REPLACE SKID CONTROL BUZZER

B

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
8.REPLACE SKID CONTROL BUZZER

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with power switch on (IG), vehicle stopped
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY