Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

This DTC is stored when the driving support ECU assembly cannot receive signals from the forward recognition camera or millimeter wave radar sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1002 Lost Communication with Gateway Module After the power switch is turned on, communication between the driving support ECU and any of the following components is abnormal for 2 seconds or more
·

Forward recognition camera

·

Millimeter wave radar sensor assembly


·

CAN bus main line, CAN bus branch line or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

No. 4 CAN junction connector



WIRING DIAGRAM

B429439E09
0.094,1.833 1.49,2.198 1.396,0.365 10 false Millimeter Wave Radar Sensor Assembly 0.104,1.667 0.563,1.865 0.458,0.198 10 false A2 5.229,2.969 7.125,3.156 1.896,0.188 10 false Driving Support ECU Assembly 5.24,2.802 5.698,3 0.458,0.198 10 false F40 0.052,4.156 4.031,4.354 3.979,0.198 10 false Forward Recognition Camera 0.052,3.979 0.51,4.177 0.458,0.198 10 false O7 0.906,3.083 1.521,3.281 0.615,0.198 10 false CANH 0.938,3.833 1.552,4.031 0.615,0.198 10 false CANL 1.365,3.083 1.521,3.281 0.156,0.198 10 false 6 1.344,3.625 1.656,3.823 0.313,0.198 10 false 12 2.771,4.146 4.708,4.385 1.938,0.24 10 false No. 4 CAN Junction Connector 2.771,3.979 3.229,4.177 0.458,0.198 10 false F72 3.146,3.094 3.427,3.271 0.281,0.177 10 false 11 3.156,3.625 3.469,3.823 0.313,0.198 10 false 22 5.792,1.927 5.948,2.125 0.156,0.198 10 false 8 5.792,2.469 5.948,2.667 0.156,0.198 10 false 9 4.094,1.906 4.344,2.115 0.25,0.208 10 false 10 4.083,2.448 4.396,2.646 0.313,0.198 10 false 21 0.917,0.771 1.531,0.969 0.615,0.198 10 false CA1P 0.927,1.51 1.542,1.708 0.615,0.198 10 false CA1N 5.958,2.01 6.573,2.208 0.615,0.198 10 false CA1P 5.958,2.552 6.573,2.75 0.615,0.198 10 false CA1N 1.375,0.771 1.531,0.969 0.156,0.198 10 false 5 3.208,0.771 3.458,0.969 0.25,0.198 10 false 9 1.365,1.302 1.521,1.5 0.156,0.198 10 false 6 3.146,1.302 3.458,1.5 0.313,0.198 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE (MALFUNCTION CONFIRMATION)
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
C334337C16
1.51,0.656 1.885,0.896 0.375,0.24 1.198,1.406 1,0.625 true 1.073,1.417 0.781,0.885 true 2.042,1.396 2.302,0.667 true 0.813,2.406 1.073,1.677 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.688 2.031,0.885 0.458,0.198 10 false F40 0.615,0.521 1.229,0.719 0.615,0.198 10 false CA1P 0.396,0.802 1.01,1 0.615,0.198 10 false CA1N 0.458,2.344 1.073,2.542 0.615,0.198 10 false GND 2.344,0.573 2.958,0.771 0.615,0.198 10 false B
*a Component with harness connected
(Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F40-8 (CA1P) - F40-9 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω:
Short circuit between bus lines
70 Ω or more:
Open circuit in a main bus line or driving support ECU assembly branch line
F40-8 (CA1P) - F40-28 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
F40-9 (CA1N) - F40-28 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
F40-8 (CA1P) - F40-7 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
F40-9 (CA1N) - F40-7 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short



Result:
Result Proceed to
OK A
NG (Open circuit in main line or Driving support ECU assembly branch line) B
NG (Short circuit between main lines) C
NG (Short to +B or ground) D



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

3.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)

C

8.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)

D

12.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY

3.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
A380143C04
1.594,0.198 1.979,0.427 0.385,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.667,0.219 2.125,0.417 0.458,0.198 10 false F40 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F40 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F40-8 (CA1P) - F40-9 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


HINT:

If the resistance is between 108 and 132 Ω, there may be an open in a CAN bus main line. If the value is 132 Ω or more, there may be an open in a CAN bus branch line between the No. 4 CAN junction connector and the driving support ECU or a connector may be disconnected.



c.

Connect the F40 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR OPEN IN CAN BUS MAIN LINES (NO. 4 CAN JUNCTION CONNECTOR)

NG

7.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
4.CHECK FOR OPEN IN CAN BUS MAIN LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.
B427446C40
1.521,0.156 1.896,0.396 0.375,0.24 2.813,0.99 2.542,1.073 true 2.542,1.438 2.823,1.479 true 2.198,1.073 2.427,0.333 true 2.375,1.813 2.208,1.438 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.594,0.198 2.052,0.396 0.458,0.198 10 false F72 2.854,0.896 3.302,1.083 0.448,0.188 10 false CANH 2.865,1.406 3.271,1.604 0.406,0.198 10 false CANL 2.25,0.156 2.865,0.354 0.615,0.198 10 false CA1P 2.219,1.833 2.833,2.031 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)


Disconnect the F72 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F72-11 (CANH) - F72-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Forward Recognition Camera
F72-9 (CA1P) - F72-20 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Millimeter Wave Radar Sensor Assembly



c.

Connect the F72 No. 4 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)

C

6.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
a.
A380142C01
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.625,0.24 1.938,0.438 0.313,0.198 10 false O7 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the O7 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-6 (CANH) - O7-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the O7 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

6.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C03
1.521,0.188 1.833,0.396 0.313,0.208 0.885,1.427 1.396,1.208 true 1.135,1.688 1.573,1.25 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.594,0.208 1.906,0.406 0.313,0.198 10 false A2 0.49,1.354 1.104,1.552 0.615,0.198 10 false CA1P 0.75,1.646 1.365,1.844 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A2 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-5 (CA1P) - A2-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the A2 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

7.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
A380143C04
1.594,0.198 1.979,0.427 0.385,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.667,0.219 2.125,0.417 0.458,0.198 10 false F40 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F40 driving support ECU assembly connector.


b.
B427446C41
1.521,0.156 1.896,0.396 0.375,0.24 2.365,1.073 2.479,0.417 true 2.51,1.802 2.385,1.438 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.594,0.198 2.052,0.396 0.458,0.198 10 false F72 2.313,0.24 2.927,0.438 0.615,0.198 10 false CA1P 2.365,1.823 2.979,2.021 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)


Disconnect the F72 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-10 (CA1P) - F40-8 (CA1P) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F72-21 (CA1N) - F40-9 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



d.

Connect the F72 No. 4 CAN junction connector.


e.

Connect the F40 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (NO. 4 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

8.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)
a.
A380142C01
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.625,0.24 1.938,0.438 0.313,0.198 10 false O7 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the O7 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-6 (CANH) - O7-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the O7 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

9.CHECK FOR SHORT BETWEEN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT BETWEEN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.
B427446C42
1.521,0.146 1.865,0.365 0.344,0.219 2.792,1.042 2.604,1.125 true 2.604,1.354 2.802,1.406 true 2.333,0.292 2.219,1.073 true 2.802,0.646 2.385,1.083 true 2.323,1.823 2.219,1.438 true 2.792,1.729 2.375,1.438 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.844,0.958 3.406,1.135 0.563,0.177 10 false CANH*b 2.844,1.323 3.375,1.51 0.531,0.188 10 false CANL*b 2.833,0.542 3.375,0.729 0.542,0.188 10 false CA1P*d 2.156,0.094 2.708,0.26 0.552,0.167 10 false CA1P*c 2.844,1.656 3.375,1.854 0.531,0.198 10 false CA1N*d 2.135,1.844 2.688,2.01 0.552,0.167 10 false CA1N*c 1.583,0.177 2.042,0.375 0.458,0.198 10 false F72
*a Front view of wire harness connector
(to No. 4 CAN junction connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly
*d to Driving Support ECU Assembly


Disconnect the F72 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F72-11 (CANH) - F72-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Forward Recognition Camera
F72-9 (CA1P) - F72-20 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Millimeter Wave Radar Sensor Assembly
F72-10 (CA1P) - F72-21 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Driving Support ECU Assembly



c.

Connect the F72 No. 4 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C
NG (Driving Support ECU Assembly Branch Line) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

C

10.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

11.CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
10.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C03
1.521,0.188 1.833,0.396 0.313,0.208 0.885,1.427 1.396,1.208 true 1.135,1.688 1.573,1.25 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.594,0.208 1.906,0.406 0.313,0.198 10 false A2 0.49,1.354 1.104,1.552 0.615,0.198 10 false CA1P 0.75,1.646 1.365,1.844 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A2 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-5 (CA1P) - A2-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the A2 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

11.CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
A380143C04
1.594,0.198 1.979,0.427 0.385,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.667,0.219 2.125,0.417 0.458,0.198 10 false F40 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F40 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F40-8 (CA1P) - F40-9 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



c.

Connect the F40 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

12.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the O7 forward recognition camera connector.

B427441C06
1.729,0.542 2.094,0.771 0.365,0.229 4.896,0.417 5.26,0.646 0.365,0.229 2.354,1.427 2.729,1.281 true 2.344,1.74 2.719,1.865 true 4.625,0.698 4.99,1.104 true 5.802,1.698 6.125,1.927 true 4.063,0.208 4.375,0.365 0.313,0.156 10 false *1 1.302,0.198 1.615,0.354 0.313,0.156 10 false *a 1.813,0.573 2.271,0.771 0.458,0.198 10 false O7 4.969,0.448 5.427,0.646 0.458,0.198 10 false F29 2.781,1.208 3.396,1.406 0.615,0.198 10 false CANH 2.781,1.802 3.396,2 0.615,0.198 10 false CANL 4.385,0.625 4.719,0.823 0.333,0.198 10 false CG 6.177,1.875 6.51,2.073 0.333,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-6 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O7-12 (CANL) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O7-6 (CANH) - F29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O7-12 (CANL) - F29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



c.

Connect the O7 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

13.CHECK FOR SHORT IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
13.CHECK FOR SHORT IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the F72 No. 4 CAN junction connector.

B427445C11
1.802,0.49 2.156,0.719 0.354,0.229 5.031,0.448 5.385,0.677 0.354,0.229 2.5,0.385 2.365,1.344 true 2.406,2.177 2.365,1.635 true 2.719,0.677 2.51,1.344 true 2.917,1.271 2.688,1.396 true 2.906,1.656 2.698,1.573 true 2.677,1.958 2.51,1.635 true 4.708,0.635 5.094,1.073 true 5.896,1.646 6.229,1.896 true 4.156,0.219 4.469,0.375 0.313,0.156 10 false *1 1.146,0.229 1.458,0.385 0.313,0.156 10 false *a 1.865,0.531 2.323,0.729 0.458,0.198 10 false F72 5.104,0.49 5.563,0.688 0.458,0.198 10 false F29 2.958,1.177 3.573,1.375 0.615,0.198 10 false CANH*b 2.969,1.594 3.583,1.792 0.615,0.198 10 false CANL*b 2.75,0.542 3.365,0.74 0.615,0.198 10 false CA1P*d 2.354,0.219 2.969,0.417 0.615,0.198 10 false CA1P*c 2.667,1.979 3.281,2.177 0.615,0.198 10 false CA1N*d 2.219,2.198 2.833,2.396 0.615,0.198 10 false CA1N*c 4.479,0.573 4.792,0.771 0.313,0.198 10 false CG 6.292,1.844 6.604,2.042 0.313,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN junction connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly *d to Driving Support ECU Assembly



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F72-11 (CANH) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward Recognition Camera
F72-22 (CANL) - F29-4 (CG)
F72-11 (CANH) - F29-16 (BAT) 6 kΩ or higher
F72-22 (CANL) - F29-16 (BAT)
F72-9 (CA1P) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly
F72-20 (CA1N) - F29-4 (CG)
F72-9 (CA1P) - F29-16 (BAT) 6 kΩ or higher
F72-20 (CA1N) - F29-16 (BAT)
F72-10 (CA1P) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Driving Support ECU Assembly
F72-21 (CA1N) - F29-4 (CG)
F72-10 (CA1P) - F29-16 (BAT) 6 kΩ or higher
F72-21 (CA1N) - F29-16 (BAT)



c.

Connect the F72 No. 4 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C
NG (Driving Support ECU Assembly Branch Line) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

C

14.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

15.CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the A2 millimeter wave radar sensor assembly connector.

B427442C07
1.854,0.385 2.198,0.604 0.344,0.219 5.031,0.396 5.375,0.615 0.344,0.219 1.344,1.885 1.771,1.573 true 2,1.563 2.188,2.094 true 4.552,0.656 5.094,1.115 true 5.896,1.708 6.198,1.958 true 4.115,0.177 4.427,0.333 0.313,0.156 10 false *1 1.292,0.188 1.604,0.344 0.313,0.156 10 false *a 1.938,0.417 2.396,0.615 0.458,0.198 10 false A2 5.094,0.427 5.552,0.625 0.458,0.198 10 false F29 4.313,0.594 4.625,0.792 0.313,0.198 10 false CG 6.25,1.906 6.708,2.104 0.458,0.198 10 false BAT 0.969,1.844 1.427,2.042 0.458,0.198 10 false CA1P 2.042,2.125 2.5,2.323 0.458,0.198 10 false CA1N
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-5 (CA1P) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-6 (CA1N) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-5 (CA1P) - F29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A2-6 (CA1N) - F29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



c.

Connect the A2 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

15.CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F40 driving support ECU assembly connector.

B427443C05
1.906,0.479 2.302,0.708 0.396,0.229 5.219,0.385 5.604,0.625 0.385,0.24 2.552,1.271 2.698,0.667 true 2.677,1.281 3.198,0.823 true 5.292,1.083 4.938,0.677 true 6.385,2.031 6.031,1.688 true 4.344,0.177 4.656,0.333 0.313,0.156 10 false *1 1.99,0.51 2.406,0.688 0.417,0.177 10 false F40 0.771,0.198 1.083,0.354 0.313,0.156 10 false *a 5.302,0.427 5.635,0.604 0.333,0.177 10 false F29 2.521,0.51 3.135,0.708 0.615,0.198 10 false CA1P 3.135,0.667 3.75,0.865 0.615,0.198 10 false CA1N 4.708,0.604 5.323,0.802 0.615,0.198 10 false CG 6.427,1.979 6.802,2.167 0.375,0.188 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F40-8 (CA1P) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F40-9 (CA1N) - F29-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F40-8 (CA1P) - F29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F40-9 (CA1N) - F29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



c.

Connect the F40 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)