Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) sends a stop light operation request signal to the stop light relay (stop light switch assembly). If the skid control ECU (brake booster with master cylinder assembly) detects a malfunction in the stop light relay circuit, the driving support ECU assembly will store DTC C1A4B.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4B Stop Light Relay Circuit Diagnosis condition:
·

Power switch on (IG) and auxiliary battery voltage between 11 and 14 V


Malfunction condition:
Either of the following conditions is met:
·

When the stop light illumination output (STPO) signal is on, a signal has not been input to the STP terminal for 0.3 seconds or more continuously.

·

When the stop light illumination output (STPO) signal is off, signals input to the STP terminal and STP2 terminal of the skid control ECU (brake booster with master cylinder assembly) differ for 0.3 seconds or more continuously.


·

Lighting system

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Stop light relay (Stop light switch assembly)

·

Wire harness or connector



WIRING DIAGRAM

B429078E07
5.042,0.417 6.365,0.635 1.323,0.219 10 false from J/B-B Fuse 5.042,1.219 6.479,1.427 1.438,0.208 10 false from IG2-NO. 2 Relay 3.51,0.552 4.125,0.75 0.615,0.198 10 false STOP 3.229,1.365 5.219,1.563 1.99,0.198 10 false ECU-IG2 NO. 3 2.625,0.313 2.781,0.51 0.156,0.198 10 false B 2.615,1.115 2.771,1.313 0.156,0.198 10 false B 5.292,4 5.75,4.198 0.458,0.198 10 false STP 5.281,3.396 5.74,3.594 0.458,0.198 10 false STPO 5.281,2.438 5.74,2.635 0.458,0.198 10 false STP2 2.625,2.458 2.781,2.656 0.156,0.198 10 false L 2.438,3.396 2.896,3.594 0.458,0.198 10 false ACC 2.438,4.01 2.896,4.208 0.458,0.198 10 false OUT 0.823,4.042 1.281,4.24 0.458,0.198 10 false GND 0.896,4.646 2.833,4.844 1.938,0.198 10 false Stop Light Switch Assembly 2.479,5.208 4.469,5.406 1.99,0.198 10 false to Stop Light 4.885,4.938 6.917,5.344 2.031,0.406 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.906,4.5 1.365,4.698 0.458,0.198 10 false A47 4.885,4.771 5.344,4.969 0.458,0.198 10 false A41 5.042,2.438 5.354,2.635 0.313,0.198 10 false 37 5.052,4 5.365,4.198 0.313,0.198 10 false 12 5.052,3.385 5.302,3.583 0.25,0.198 10 false 22 2.802,2.458 2.958,2.656 0.156,0.198 10 false 3 2.802,3.396 2.958,3.594 0.156,0.198 10 false 4 2.792,4 2.948,4.198 0.156,0.198 10 false 1 2.802,0.313 2.958,0.51 0.156,0.198 10 false 7 2.802,1.115 2.958,1.313 0.156,0.198 10 false 6 0.677,4.042 0.833,4.24 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When this DTC is output, a malfunction in the lighting system is suspected. Check if the lighting system is functioning normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT HYBRID SYSTEM START
a.

Depress the brake pedal, push the power switch and check that the power switch turns on (READY).

OK:

The power switch turns on (READY).



Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:

The stop lights illuminate when the brake pedal is depressed. The stop lights turn off when the brake pedal is released.



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT RELAY (STOP LIGHT SWITCH ASSEMBLY)

NG

3.INSPECT STOP LIGHT RELAY (STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the power switch off.


b.

Inspect the stop light relay (stop light switch assembly).

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light relay (stop light switch assembly) is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

NG

REPLACE STOP LIGHT RELAY (STOP LIGHT SWITCH ASSEMBLY)

4.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

5.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)
a.

Turn the power switch off.


b.
B435101C02
1.552,0.333 1.948,0.563 0.396,0.229 2.188,1.667 2.521,0.563 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 2.375,0.385 2.99,0.583 0.615,0.198 10 false STPO 1.625,0.365 2.021,0.573 0.396,0.208 10 false A41
*a Front view of wire harness connector
(to Skid control ECU (Brake booster with master cylinder assembly))


Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-22 (STPO) - Body ground Always 11 to 14 V



d.

Connect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT RELAY)

NG

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - SKID CONTROL ECU)
6.PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT RELAY)
a.

According to the display on the Techstream, perform the Active Test Stop Light Relay.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Stop Light Relay
Data List Display
Stop Light Relay Output
50004 105 5 291

b.

According to the display on the Techstream, perform the Data List Stop Light Relay Output.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (Stop light switch assembly)
(STPO terminal output)
ON or OFF ON: Output
OFF: Not output
-

c.

Check that the Data List item Stop Light Relay Output changes between ON and OFF and the stop lights turn on and off according to the operation of the Active Test.


Result:
Result Proceed to
The Data List item Stop Light Relay Output does not change between ON and OFF and the stop lights do not turn ON and OFF according to the operation of the Active Test. A
The Data List item Stop Light Relay Output changes between ON and OFF but the stop lights do not turn ON and OFF according to the operation of the Active Test. B



A

7.INSPECT SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - SKID CONTROL ECU)
7.INSPECT SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

According to the display on the Techstream, perform the Active Test Stop Light Relay.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

b.

Measure the voltage according to the value(s) in the table below.

HINT:

Do not disconnect the stop light relay (stop light switch assembly) connector.



Standard Voltage:
Tester Connection Condition Specified Condition
A47-4 (ACC) - Body ground Power switch on (IG)
(Active test OFF)
11 to 14 V
Power switch on (IG)
(Active test ON)
Below 1.5 V


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT RELAY (STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - SKID CONTROL ECU)
a.

Turn the power switch off.


b.

Disconnect the A47 stop light relay (stop light switch assembly) connector.


c.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-1 (OUT) - A41-12 (STP) Always Below 1 Ω



e.

Connect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


f.

Connect the A47 stop light relay (stop light switch assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - SKID CONTROL ECU)
a.

Turn the power switch off.


b.

Disconnect the A47 stop light relay (stop light switch assembly) connector.


c.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-4 (ACC) - A41-22 (STPO) Always Below 1 Ω
A47-4 (ACC) or A41-22 (STPO) - Body ground Always 10 kΩ or higher



e.

Connect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


f.

Connect the A47 stop light relay (stop light switch assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT RELAY (STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR